Stop and call a pro now if
- You smell burning or see smoke from the washer. Turn it off and unplug it if you can do so safely, or turn off its breaker.
- Water is leaking onto the floor near the outlet or cord. Turn off the breaker before touching the washer or the plug.
- The washer trips its breaker again after one reset. Leave the breaker off and call a technician.
Likely causes
-
An unbalanced load
Whirlpool says the washer may stop spinning if it detects a significant imbalance. GE models show a flashing Spin light or Balancing message. Heavy single items like a bath mat or a few towels are common culprits.
-
The lid was opened or isn't closed
GE says opening the lid pauses the washer, and it won't restart until you close the lid and press Start. A lid that doesn't close fully can keep the lid switch from engaging.
-
Low spin or no spin was selected
Whirlpool notes cycles with low spin speeds remove less water, and with Low Spin or No Spin selected the washer may not spin the clothes as dry as you expect.
-
Too much detergent
Too many suds can slow draining, and a washer won't spin until the water is out. Use HE detergent in the amount the label gives, or one pod per load.
-
Water can't drain
A washer won't spin a tub full of water. A kinked or clogged drain hose or a clogged pump filter stops the cycle.
-
A worn lid switch, belt, coupling or motor
If the load is balanced, the lid is closed and the water drains, a failed part is likely. HomeGuide lists the lid switch, drive belt, coupling, clutch and motor among common washer repairs. These need a technician.
What you can safely check
Unplug the washer before reaching into the drum or touching the drain filter.
-
Redistribute the load
Spread wet items evenly around the drum and remove a few if it is packed. Then select Drain & Spin and press Start, as GE and Whirlpool both suggest.
-
Close the lid or door firmly
Make sure nothing is caught in it. On a top-loader, check that the lid isn't bent and closes fully.
-
Check the spin setting
Choose a normal or heavy-duty cycle with a high spin speed and run Drain & Spin.
-
Check for suds
If the drum is full of suds, run a rinse with no detergent and use less HE detergent next time.
-
Check the drain hose
Straighten any kinks and make sure the hose isn't pushed too far into the standpipe. On front-loaders with an access panel, clean the pump filter. Let hot water cool first, and expect several gallons: use the drain tube if there is one and have towels and more than one shallow pan ready.
-
Check that it is level
Whirlpool lists an unlevel washer as a cause. Rock it gently corner to corner. If it wobbles, adjust the feet.
-
Give it a few minutes
GE notes full-size top-loaders can pause for up to three minutes between parts of the cycle, such as after agitation and before the spin.
-
Reset the washer
Unplug it for one minute, then plug it back in and try Drain & Spin again. GE has a separate motor reset for select top-loaders with its Hydrowave wash system. Check GE's instructions for your model.
Avoid these
- Bypassing or taping down the lid switch to force a spin. It is a safety switch.
- Reaching into the drum while it is moving.
- Running cycle after cycle if you smell burning or hear grinding.
When to call a pro
- The washer drains but still won't spin with a balanced load.
- The drum hums, clicks or grinds but won't turn.
- The washer won't drain even after the hose and filter are clear.
- The control shows an error code that keeps coming back.
Tell the technician the brand and model number from the label, whether it is a top-loader or front-loader, any error code, and whether the water drains. That helps them bring the right lid switch, belt, coupling or pump.
Typical repair costs
National ranges for parts and labor from HomeGuide. Many repair companies charge a minimum service fee.
| Repair | Typical cost | Source |
|---|---|---|
| Minimum service fee | $70–$130 | HomeGuide |
| Lid switch or door lock | $100–$300 | HomeGuide |
| Drive belt | $100–$200 | HomeGuide |
| Drive coupling | $100–$250 | HomeGuide |
| Drain pump | $150–$350 | HomeGuide |
| Clutch (top-load) | $200–$300 | HomeGuide |
| Motor | $300–$700 | HomeGuide |
| Control board | $350–$550 | HomeGuide |
Frequently asked questions
Why does my washer fill and agitate but not spin?
Start with the load: GE says a flashing Spin light or Balancing message means the load needs redistributing. Then wait a few minutes, since GE top-loaders can pause before the spin. If a balanced Drain & Spin still won't spin, a lid switch, belt or coupling may have failed.
Why are my clothes still soaking wet after a cycle?
A low or no spin setting, an unbalanced load, too many suds or a drain problem are the usual causes. Whirlpool suggests running Drain & Spin after rearranging the load.
Will my washer spin if water is standing in the tub?
No. Whirlpool says to check the drain hose installation if water is standing in the tub. A washer won't spin until the water drains.
How much does it cost to fix a washer that won't spin?
It depends on the part. HomeGuide puts a lid switch at $100 to $300, a belt at $100 to $200 and a motor at $300 to $700.
Sources
- Top Load Washer - Does Not Spin , GE Appliances
- Not Spinning - Washer , Whirlpool
- Washer Not Draining or Spinning? Troubleshooting Guide , Whirlpool
- How Much Does Washing Machine Repair Cost? , HomeGuide