Stop and call a pro now if
- You smell gas (a rotten-egg smell). Turn the oven off if you can do so right away, leave the house without switching anything else on or off, and call your gas utility or 911 from outside.
- You see sparks or flames from an electric element, or a spot on it keeps glowing after you turn the oven off. Turn off the range's breaker and keep the door closed. If flames don't go out within a few seconds, get everyone out and call 911.
- The range's breaker trips again after you reset it once.
- You smell burning plastic or wiring from the control panel.
- Your carbon monoxide alarm sounds. Get everyone outside and call 911.
Likely causes
-
Settings, Sabbath mode or a locked door
GE notes the oven won't heat unless Bake or Broil is selected and Start is pressed on electronic controls. Sabbath mode or a self-clean latch left locked also stops it.
-
Power to the range
GE says to check the breaker or fuses and whether the cord is fully plugged in. A gas range still needs power for its igniter and controls.
-
A failed bake element (electric)
GE says to check the lower bake element for cracks or breaks. HomeGuide notes elements burn out or crack over time and the oven can't heat properly.
-
A weak or failed igniter (gas)
Many gas ovens use a glow-bar igniter. GE says to look for its red glow with the oven on, and no glow points to the igniter or controls. An igniter that glows but is too weak to open the gas valve is a common failure. Some newer ovens use spark ignition, which clicks instead of glowing. Check your manual for which type you have.
-
The gas regulator is off (new installs)
GE notes the regulator on a gas range can be bumped to off during installation. The burners on top still work but the oven won't.
-
Damage after a self-clean cycle
If the oven stopped heating right after a self-clean, the cycle's heat may have blown the thermal fuse or damaged a control part. Tell the technician.
-
A sensor, thermostat, thermal fuse or control board
These control the heat. A faulty one can stop the oven heating or make it heat unevenly.
What you can safely check
Find out first whether the oven is gas or electric. Turn off the breaker before touching any oven part.
-
Check the settings
Select Bake, set a temperature and press Start. Make sure the oven isn't in Sabbath mode or a delayed or timed cook.
-
Check the door latch
On self-clean ovens with a manual latch, GE says to make sure it is fully in the unlocked position.
-
Reset the control
GE suggests turning the range's breaker off for one minute, then back on, even if the clock still works.
-
Electric: watch the bake element
Set Bake and watch the lower element through the window. It should glow red within a few minutes. If not, turn off the breaker, let the oven cool and look for cracks, breaks or blisters. If the element is hidden under the oven floor, leave it to a technician.
-
Gas: check the burners and igniter
If the cooktop burners light, gas is reaching the range. Turn on the oven and look through the door window or the broiler opening, without removing any panels. A glow-bar igniter should glow and light the burner within a minute or two. Write down what you see. If your oven uses spark ignition, listen for clicking instead.
Avoid these
- Trying to light a gas oven burner with a match or lighter.
- Testing an igniter or element with a meter while the range is powered. Leave electrical testing to a technician.
- Using the oven to heat your home, or leaving the oven door open to warm a room. A gas oven used this way can produce dangerous carbon monoxide.
When to call a pro
- The bake element is cracked or hidden. A technician can match the right part to your model.
- A gas oven's igniter doesn't glow, or glows but the burner never lights.
- The oven heats but far below the set temperature.
- The control shows an error code or the oven won't respond.
Tell the technician the brand and model number, whether the range is gas or electric, and what you saw: no glow, a broken element, an error code or slow heating. That helps them bring the right element, igniter, sensor or board.
Typical repair costs
National ranges for parts and labor from HomeGuide.
| Repair | Typical cost | Source |
|---|---|---|
| Typical oven repair | $150–$350 | HomeGuide |
| Heating element replacement | $150–$450 | HomeGuide |
| Gas oven igniter replacement | $150–$325 | HomeGuide |
| Temperature sensor | $100–$250 | HomeGuide |
| Thermostat | $100–$350 | HomeGuide |
| Thermal fuse | $100–$250 | HomeGuide |
| Gas oven safety valve | $150–$400 | HomeGuide |
| Control board | $150–$600 | HomeGuide |
Frequently asked questions
Why are my stove burners working but not my oven?
On an electric range, a failed bake element is a common cause. On a gas range, it is usually the oven igniter. GE also notes that on a new gas install, the regulator may have been bumped to off.
How do I know if my oven's bake element is bad?
With the power off and the oven cool, look for cracks, breaks or blistered spots on the lower element. GE says a cracked or broken element needs to be replaced.
Why does my gas oven igniter glow but not light?
An igniter can glow but still be too weak to open the oven's gas safety valve. Igniter replacement is the most common fix. HomeGuide puts it at $150 to $325.
Is it worth fixing an oven that won't heat?
Usually. Most single-part repairs run $150 to $450, while HomeGuide puts a new oven at $700 to $1,600.
Sources
- Range & Wall Oven - Oven Will Not Come On , GE Appliances
- Gas Range - Oven Does Not Heat, But The Burners Heat , GE Appliances
- How Much Does Oven Repair Cost? , HomeGuide