Washer Not Draining? Causes, Safe Checks and Costs

A washer that won't drain is most often blocked: a kinked or clogged drain hose, a full pump filter, or a household drain that can't take the water. Lid or door locks, oversudsing and unbalanced loads can also stop the drain. A failed pump or control is a job for a technician.

Stop and call a pro now if

  • You smell burning or hear a loud hum with the tub full of water. Unplug the washer.
  • Water is spreading toward an outlet or power cord. Don't touch the plug while standing in water. Switch off the washer's breaker first.
  • The standpipe or a floor drain is overflowing. The blockage may be in the house drain, so stop using water in the house and call a plumber.

Likely causes

  • A kinked or clogged drain hose

    GE and Whirlpool both list a kinked or clogged drain hose as a first check. Socks and small items often end up in the hose.

  • A clogged pump filter

    Many front-load washers have a drain pump filter behind a small door at the bottom front. Whirlpool notes it can clog with lint, dirt and small items.

  • The standpipe is too high or blocked

    Whirlpool sets the maximum standpipe height at 96 inches. Water backs up if the pipe is too high or the house drain is clogged.

  • Too many suds

    Whirlpool notes that too much detergent can stop the washer from pumping water out. Use HE detergent in an HE washer.

  • The lid or door isn't latched

    The washer won't drain or spin if the lid switch or door lock doesn't register a closed door.

  • An unbalanced or overloaded load

    The washer may stop to protect itself, leaving water in the tub.

  • A failed drain pump or control

    If the tub is full and the washer hums without draining, GE says it needs service.

What you can safely check

Unplug the washer before checking the hose or the pump filter. Have towels and a shallow pan ready. If you were running a hot cycle, let the water cool first.

  1. Give it a few minutes

    GE notes some washers pause for up to 3 minutes during a cycle. Make sure it is truly stuck before you intervene.

  2. Run a drain and spin cycle

    Choose Drain/Spin or Rinse and Spin with a high spin speed. Gentle cycles spin slowly and leave more water.

  3. Check the drain hose

    Pull the washer out and straighten any kinks. Remove the hose from the standpipe only when the tub is empty, or with a bucket ready, then check it for a clog.

  4. Test the standpipe

    GE suggests pouring about a quart of water into the standpipe. If it backs up, the problem is the house drain and a plumber should clear it.

  5. Clean the pump filter (front-loaders)

    Open the small door at the bottom front and drain the water with the short hose if there is one. A front-loader can hold several gallons, so drain a little at a time and close the cap between pans. Then unscrew the filter slowly and clear it.

  6. Redistribute the load

    Spread out heavy items like towels and jeans, or remove some, and try again.

Avoid these

  • Forcing a locked front-load door open with water inside.
  • Pouring chemical drain cleaner into the washer or the drain hose.
  • Opening the pump filter without a pan and towels. A full tub drains out through it.

When to call a pro

  • The tub stays full and the washer hums without draining.
  • The hose, filter and standpipe are clear and it still won't drain.
  • You hear grinding from the pump, or the washer shows a drain error code.
  • The house drain backs up, which needs a plumber rather than an appliance tech.

Tell the technician the brand, model and age, whether it is a top or front loader, any error code, and whether you heard the pump run. That separates a pump, lid lock or control problem.

Typical repair costs

National ranges for parts and labor from HomeGuide.

Repair Typical cost Source
Typical washer repair $100–$400 HomeGuide
Drain pump replacement $150–$350 HomeGuide
Drain hose replacement $100–$200 HomeGuide
Lid switch or door lock $100–$300 HomeGuide
Pressure switch $100–$250 HomeGuide
Control board $350–$550 HomeGuide

HomeGuide notes many repair companies charge a minimum service fee of $70 to $130, sometimes credited to the repair.

Frequently asked questions

How do I get water out of a washer that won't drain?

Unplug it. On a front-loader, drain through the pump filter door into a shallow pan. On a top-loader, bail it out or lower the drain hose into a bucket below the tub.

Why does my washer drain but not spin?

Often an unbalanced load, a gentle cycle with a slow spin, oversudsing or a lid or door lock that doesn't register as closed.

Can too much detergent stop a washer from draining?

Yes. Whirlpool notes excess suds can stop the washer from pumping and spinning. Measure HE detergent to the line.

Is it worth repairing a washer that won't drain?

A clogged filter or hose costs nothing to fix. A pump replacement is usually worth it on a washer that is otherwise in good shape.

Sources

  1. Front Load Washer - Will Not Drain or Drains Slowly , GE Appliances
  2. Washer Not Draining or Spinning? Troubleshooting Guide , Whirlpool
  3. How Much Does Washing Machine Repair Cost? , HomeGuide