Dryer Not Heating? Causes, Safe Checks and Repair Costs

A dryer that tumbles but stays cold usually has a power, gas or airflow problem. An electric dryer needs full 240-volt power to heat even though it can run without it. A clogged vent can overheat the dryer and blow a safety fuse. Burned-out elements, igniters and fuses are common repairs.

Stop and call a pro now if

  • You smell burning or see smoke. Stop the dryer and unplug it. If there is fire, get everyone out and call 911.
  • You smell gas near a gas dryer. Leave without switching anything on or off, and call your gas utility or 911 from outside.
  • The power cord or the outlet is scorched, melted or hot to the touch. Don't touch the plug. Turn off the dryer's breaker and call an electrician or a technician.

Likely causes

  • Half of a double breaker tripped (electric)

    GE explains an electric dryer can run on partial 120-volt power but won't heat without full 208/240 volts. A partly tripped breaker can look normal, so switch it fully off, then on.

  • The wrong cycle

    GE notes the dryer won't heat on Air Fluff or a cool-down setting.

  • A clogged vent

    Lint in the vent cuts airflow. NPS fire guidance notes that lint buildup can make a dryer overheat. Safety devices then shut the heat off.

  • A blown thermal fuse or failed thermostat

    These safety parts cut the heat, or on some models stop the dryer altogether, when it overheats. A blown thermal fuse often points back to a restricted vent.

  • A burned-out heating element (electric)

    A burned-out element is a common reason an electric dryer runs without heat.

  • Gas supply, igniter or valve coils (gas)

    GE says to make sure the gas line is on. If it is, a failed igniter or gas valve coil is the usual cause.

  • A damaged power cord connection (electric)

    GE notes a burned or loose connection at the terminal block behind the dryer can stop it heating.

What you can safely check

Unplug the dryer before you look at the vent or move it.

  1. Check the cycle

    Choose a timed or automatic dry cycle with heat, not Air Fluff or cool down.

  2. Reset the breaker (electric)

    Switch the dryer's double breaker fully off, then on. GE says a partly tripped breaker can look normal.

  3. Check the gas valve (gas)

    Make sure the valve on the dryer's gas line is open, especially after a move or a new install.

  4. Clean the lint screen

    Clean it before every load. NPS lists this as a basic step to prevent dryer fires.

  5. Check the vent

    On a gas dryer, move it gently so you don't kink or strain the gas connector, and if you smell gas afterward, leave and call from outside. Disconnect the vent at the back of the dryer and look for lint. Go outside with the dryer running and check that air pushes the vent flap open.

  6. Check the cord (electric, if comfortable)

    With the dryer unplugged, GE describes removing the cover at the back to look for burned or loose wires at the terminal block. If you see damage, stop using the dryer and have a technician replace the cord or terminal block. The wall outlet may need an electrician as well.

Avoid these

  • Bypassing or jumping a thermal fuse or thermostat to get heat back.
  • Using plastic or thin foil accordion vent hose. NPS recommends rigid or flexible metal venting from the dryer to the wall outlet.
  • Leaving the dryer running when you are out or asleep while you troubleshoot.

When to call a pro

  • The breaker, cycle and vent check out and it still won't heat.
  • The thermal fuse has blown more than once.
  • A gas dryer won't light with the gas on.
  • You find scorched wiring or a melted terminal block.

Tell the technician whether the dryer is gas or electric, its brand and age, and whether it heated at all before stopping. If a fuse blew, have the vent cleaned too, or the new fuse will likely blow again.

Typical repair costs

National ranges for parts and labor from HomeGuide.

Repair Typical cost Source
Typical dryer repair $100–$300 HomeGuide
Heating element replacement $150–$350 HomeGuide
Thermal fuse replacement $75–$150 HomeGuide
Thermostat replacement $100–$300 HomeGuide
Igniter replacement (gas) $100–$250 HomeGuide
Dryer vent cleaning $80–$185 HomeGuide

HomeGuide notes many repair companies charge a minimum service fee of $70 to $130. If the vent is crushed or too long, replacing it costs more than a cleaning.

Frequently asked questions

Why does my dryer run but not get hot?

Common causes are a partly tripped breaker, the wrong cycle, a clogged vent, a blown thermal fuse, or a failed element or igniter.

Can a clogged dryer vent stop a dryer from heating?

Yes. Poor airflow makes the dryer overheat, and its safety parts cut the heat. It is also a fire risk, so clean the vent before replacing parts.

How often should a dryer vent be cleaned?

NPS guidance says vents should be cleaned periodically, and at least once a year in shared laundry rooms. Clean it sooner if loads take longer to dry.

Is it safe to use a dryer that isn't heating?

Running it on air only is not dangerous by itself, but stop if you smell burning or the cabinet gets unusually hot.

Sources

  1. Electric Dryer - Runs But Does Not Heat , GE Appliances
  2. Gas Dryer - Runs But Does Not Heat , GE Appliances
  3. Fire Prevention 52: Dryer Fires , U.S. National Park Service
  4. How Much Does Dryer Repair Cost? , HomeGuide