Garage Door Won't Close? Causes, Safe Checks and Costs

If the door starts down and reverses, or won't move at all and the opener lights flash, the safety sensors near the floor are the usual cause. A few minutes of cleaning and realigning fixes most of them. A door that is crooked, off its track or suddenly very heavy has a hardware problem that a technician needs to fix.

Stop and call a pro now if

  • The door is crooked, a roller has come out of the track, or a cable is loose or frayed. Stop using the door and keep people and cars out from under it.
  • You heard a loud bang, or you see a gap in the spring above the door. A spring has probably broken. Don't run the opener.
  • The door doesn't reverse when something is in its path. Stop using the automatic opener until it is fixed.

Likely causes

  • Blocked or misaligned safety sensors

    The two photo-eyes a few inches above the floor on each side must see each other before the opener will close the door. A broom, trash can or leaves in the beam, or a sensor knocked out of line, makes the door reverse. On Chamberlain and LiftMaster openers the lights flash 10 times when this happens.

  • Dirty sensor lenses or bright sun

    Dust, cobwebs or direct low sun on the receiving eye can interrupt the beam.

  • The wall control is locked

    Many wall buttons have a lock or vacation setting that disables the remotes. The door will still work from the wall button.

  • Something in the track

    A bent track, debris, or a damaged roller can make the door bind. The opener reads the resistance as an obstruction and reverses.

  • A broken spring or cable

    The springs carry the door's weight. With one broken, the opener struggles or stops, and the door may close unevenly or not at all.

  • Close-limit or force settings

    A door that touches the floor and then goes back up usually has its close-limit or force setting off, which can happen after a power outage or opener reset. Adjusting them is in the opener manual, but a technician should check why they changed.

  • Remote or opener electronics

    A dead remote battery affects only the remote. If the wall button works, start there. Opener boards can also fail.

What you can safely check

Start at the floor. Most no-close problems are the sensors, and you can check them without tools or ladders.

  1. Clear the doorway

    Move anything near the door's path or the sensor beam, including things hanging in the opening.

  2. Read the sensor lights

    Each sensor has a small LED. On Chamberlain and LiftMaster units, the sending eye glows steady amber and the receiving eye glows steady green. A green light that is off or flickering means the beam is blocked or misaligned. If both lights are off, the problem is the wiring or the opener, not the alignment.

  3. Clean the lenses

    Wipe both lenses with a soft dry cloth.

  4. Realign a sensor

    Loosen the wing nut on the bracket, point the two eyes straight at each other at the same height, and tighten it again once both lights are steady.

  5. Close it from the wall button

    Many openers will close despite a sensor fault if you press and hold the wall button until the door is fully down. Check your opener's manual. Watch the door the whole way and keep the doorway clear. Then fix the sensors.

  6. Check the lock button

    If the remotes do nothing, look for a lock or vacation light on the wall control and turn it off as the manual describes.

  7. Test the reversal

    Once the door closes, keep people and pets clear of the door path and lay a 2x4 flat on the floor in its path. The door should reverse when it touches the board. If it doesn't, stop using the opener and call for service.

Avoid these

  • Adjusting, loosening or removing springs, cables, drums or the bottom brackets. They are under high tension and can cause serious injury.
  • Pulling the emergency release while the door is open. If a spring is broken, the door can fall. Use the release only with the door closed.
  • Taping sensors together or bypassing them so the door will close.
  • Hammering a bent track back into place with the door on it.

When to call a pro

  • The sensors are aligned and clean, both lights are steady, and the door still reverses.
  • The door is crooked, binds, or has a roller out of the track.
  • A spring is broken or a cable is loose or frayed.
  • The door fails the 2x4 reversal test.

If the door is stuck open, ask whether the company offers same-day or emergency service. Don't try to force it closed yourself if a spring or cable is damaged.

Typical repair costs

National ranges from HomeGuide and HomeAdvisor. Sensor and alignment calls sit at the low end, while spring and off-track repairs cost more.

Repair Typical cost Source
Typical garage door repair $150–$350 HomeGuide
Safety sensor replacement $125–$300 HomeGuide
Sensor realignment (service visit) $150–$250 HomeAdvisor
Opener repair $100–$200 HomeGuide
Track repair or realignment $125–$300 HomeGuide
Off-track door repair $200–$350 HomeGuide
Spring replacement $150–$350 HomeGuide
Cable replacement $150–$350 HomeGuide

HomeAdvisor puts the average garage door repair at $265. A new opener runs $300 to $900 installed, according to HomeGuide.

Frequently asked questions

Why does my garage door go down and then back up?

The opener thinks something is in the way. Most often the photo-eye sensors are blocked, dirty or misaligned. It can also be a bent track or binding door that the opener reads as an obstruction.

Why do my garage door opener lights flash?

On Chamberlain and LiftMaster openers, lights flashing 10 times when the door won't close means the safety sensors are blocked or misaligned.

Can I close the garage door manually?

Only with the door already closed, or by holding the wall button down as above. Pull the emergency release only when the door is closed and the springs and cables look intact. Never pull it with the door open or if you suspect a broken spring.

How do I know if the problem is the sensors?

Check the LEDs on both sensors. If the receiving one is off or flickering while the other is steady, the beam isn't connecting.

Sources

  1. Why do the lights on my garage door opener flash and my door will not close? , Chamberlain Group
  2. Safety Tips for Garage Door Systems , DASMA
  3. Garage Door Repair Cost , HomeGuide
  4. Garage Door Sensor Replacement Cost , HomeGuide
  5. How Much Does Garage Door Repair Cost? , HomeAdvisor