Stop and call a pro now if
- You heard a loud bang from the garage and the door now feels very heavy or won't lift. A spring has likely broken. Leave the door where it is. Don't run the opener or pull the emergency release, because an open door with a broken spring can drop. Keep people and cars out from under it and call a technician.
- A cable is frayed or loose, or the door hangs crooked in its tracks. Don't run the door.
- The door doesn't reverse when it closes on an object during the safety test.
Likely causes
-
Dry rollers, hinges and bearings
Chamberlain's owner's manuals call for oiling the door rollers, bearings and hinges once a year. When they dry out, they squeak and grind.
-
Chain or belt tension
Chamberlain says if the opener is noisy with the door disconnected, check the tension of the chain or belt. A screw-drive opener needs its screw lubricated.
-
Worn rollers or loose hardware
Rollers with worn bearings, and loose hinges or track bolts, rattle as the door moves. A tune-up usually covers tightening and adjustment.
-
Opener vibration
Chamberlain notes a vibration reduction kit or isolator can help an opener that shakes the ceiling once the door is maintained and the drive tension is right.
-
An unbalanced door or spring problem
A door that is hard to lift by hand or won't stay put halfway is out of balance. That strains the opener and needs a technician.
What you can safely check
Chamberlain's method separates door noise from opener noise. Do these with the door fully closed.
-
Look at the springs first
With the door closed, look at the springs above the door or along the tracks. A gap in a coil means a spring is broken. Stop here and call a technician.
-
Disconnect the door with it closed
With the door all the way down, pull the emergency release cord. Don't pull it with the door open: if a spring is broken, the door can drop.
-
Move the door by hand
Lift it slowly, only a foot or two at first. Chamberlain says it should move smoothly and be balanced. Listen for squeaks or grinding from the rollers and hinges. If it feels heavy or binds, lower it slowly back to the floor while it is still only a foot or two up. If it starts to drop faster than you can control, let go and step back. Never hold it up or reach under it, and keep children clear. Call a technician.
-
Oil the rollers, hinges and bearings
Use a garage door lubricant on hinge pivots, roller bearings and the spring bearing plates. Chamberlain says not to grease the tracks.
-
Run the opener on its own
With the door still disconnected, run the opener. If it is loud by itself, unplug it, then check the chain or belt tension against your manual, or lubricate the screw on a screw-drive model. Grinding while the motor runs but the trolley doesn't move usually means a worn drive gear, which is technician work.
-
Reconnect and test
Reconnect the door to the opener, then do the safety tests: the door must reverse when it closes on a 2x4 laid flat on the floor, and when you pass an object through the photo-eye beam while it closes.
Avoid these
- Touching or adjusting the springs, cables or bottom brackets. DASMA warns these are under extreme tension and can cause serious injury.
- Greasing or oiling the tracks. Chamberlain says the tracks should stay clean and dry.
- Opening the opener's housing. Internal gear and sprocket repairs are technician work.
When to call a pro
- The door is heavy, uneven or won't stay halfway open.
- You see a broken spring, frayed cable or bent track.
- The noise continues after lubrication and tension checks.
- The door fails the reversal safety test.
Tell the technician whether the noise comes from the door or the opener, based on the disconnect test, and what kind of noise it is. That points the visit at rollers, springs, the drive or the opener's gears.
Typical repair costs
National ranges for parts and labor from HomeGuide. Some companies charge a minimum service fee.
Frequently asked questions
What should I use to lubricate a garage door?
Use a garage door lubricant on the hinges, roller bearings and spring bearing plates. Chamberlain says not to grease the tracks, and the opener itself usually needs no extra lubrication apart from a screw drive's screw.
Why is my garage door opener so loud?
If the opener is loud with the door disconnected, Chamberlain points to chain or belt tension, an unlubricated screw drive or, rarely, dry internal gears. Belt-drive openers are generally quieter than chain drives.
Is a squeaky garage door dangerous?
Squeaks alone usually mean dry hardware. A loud bang, a heavy door or a frayed cable is different and needs a technician.
How often should a garage door be serviced?
Chamberlain's owner's manuals call for oiling the rollers, bearings and hinges every year. HomeGuide suggests an annual inspection and tune-up.
Sources
- How to Troubleshoot Noise Issues with Garage Door Openers , Chamberlain Group
- Safety Tips for Garage Door Systems , DASMA
- Garage Door Repair Cost , HomeGuide