Stop and call a pro now if
- A spring is broken (you heard a loud bang, or see a gap in the spring above the door). Don't run the opener and don't lift the door. If the door is closed, leave it closed. If it is open, keep people and cars out from under it and don't try to close it. Call a technician.
- A lift cable is frayed or has come off its drum, or the door hangs crooked or has come off its track.
- You smell burning from the opener motor, or it hums without moving the door. Unplug it.
Likely causes
-
Lock mode is on
Chamberlain explains that with Lock (vacation) mode on, the opener ignores remotes. The lights flash twice when you press the remote, and the wall control's light may flash.
-
A dead remote battery
A weak battery is the most common reason a single remote stops working while the wall button still does.
-
The remote lost its programming
Chamberlain notes that holding the opener's Learn button too long erases all programmed remotes and keypads.
-
No power to the opener
A tripped breaker, a tripped GFCI outlet in the garage or a loose plug cuts power. Nothing works, including the light.
-
Safety sensors blocked or misaligned
If the door starts down, then reverses, and the opener light flashes, the photo eyes near the floor aren't seeing each other.
-
The trolley is disengaged
If someone pulled the red emergency release cord, the motor runs but the door doesn't move until the trolley reconnects.
-
A broken spring or cable
The springs do the lifting. With one broken, the opener strains and the door may only rise a few inches or not at all.
-
A worn gear or failed motor
The motor hums or runs but the chain or belt doesn't move, or nothing happens with power present.
What you can safely check
Test the wall button and a remote first. The answer tells you which checks to do.
-
Wall button works, remote doesn't
Check whether the opener lights flash twice when you press the remote. If they do, press and hold the wall control's Lock button until its light stops flashing, as Chamberlain describes.
-
Replace the remote battery
Many Chamberlain and LiftMaster remotes take a 3V CR2032 coin cell, but older remotes use other types, so check the one inside yours. Match the polarity and test again.
-
Test range and reprogram
Chamberlain suggests testing right under the opener, then farther away. If it only works up close, LED bulbs in the opener can cause interference. If it doesn't work at any distance, reprogram the remote.
-
Nothing works
Check that the opener is plugged in, reset any tripped GFCI outlet in the garage, and check the breaker.
-
Door reverses or won't close
Clean the sensor lenses near the floor, clear anything in the path, and check that both indicator lights are on.
-
Test the safety reverse
After any sensor work, lay a 2x4 flat on the floor in the door's path and close the door. It should reverse when it touches the board. If it doesn't, stop using the opener and call a technician.
-
Motor runs, door doesn't move
With the door fully closed, check whether the trolley on the rail has been released. Your manual explains how to re-engage it. Look at the springs and cables before running the opener again.
Avoid these
- Adjusting, loosening or replacing springs, cables or bottom brackets. They are under high tension. DASMA advises having springs inspected and replaced by a professional technician.
- Pulling the emergency release while the door is open. With a weak or broken spring, the door can drop.
- Taping down or bypassing the safety sensors.
When to call a pro
- A spring or cable is broken or worn.
- The motor hums, runs without moving the door, or smells hot.
- The door is off track, bent or hanging unevenly.
- The opener still doesn't respond with power present and the wall button pressed.
Tell the technician the opener brand and age, whether the wall button works, and whether the motor runs. If your door has two springs, DASMA recommends replacing both, even if only one broke.
Typical repair costs
National ranges for parts and labor from HomeGuide.
Frequently asked questions
Why does my garage door open with the wall button but not the remote?
Lock mode, a dead remote battery or lost programming. If the opener lights flash twice when you press the remote, lock mode is on.
Why does my garage door opener run but the door won't move?
Either the trolley has been disengaged by the emergency release, or a spring, cable or drive gear has failed. Check the springs before you try again.
Can I open my garage door by hand if the opener doesn't work?
With the door closed and the springs intact, you can pull the emergency release and lift it by hand. If a spring is broken, the door is very heavy and can fall, so leave it closed.
Why does my garage door go down and then back up?
The safety sensors aren't seeing each other, something is in the way, or the opener's settings need adjusting by a technician. Never turn up the force to make a sticking door close.
Sources
- Remote Control: Remote Does Not Work , Chamberlain Group
- Safety Tips for Garage Door Systems , DASMA
- Garage Door Repair Cost , HomeGuide
- How Much Does a Garage Door Opener Installation Cost? , HomeGuide