7 Insulation Types Compared by R-Value and Cost (2026 Guide)

1. Fiberglass Batts: The Budget-Friendly Baseline

Fiberglass batts deliver R-2.9 to R-3.8 per inch at $0.40-$0.70 per square foot, making them the most affordable option for walls, attics, and floors. DIY installation costs $750-$1,500 for a typical attic, while professional installation runs $1,500-$3,000. The lower R-value means you'll need greater depth to achieve the same thermal resistance as premium materials.

4-8 hours DIY utility knifemeasuring tapestaple gunsafety glassesrespirator

Pro tip: Install fiberglass with the vapor barrier facing the warm side of the wall to prevent moisture accumulation. In cold climates, this means the barrier faces inward; in hot climates, it faces outward.

2. Blown-In Fiberglass: Better Coverage for Irregular Spaces

Blown-in fiberglass achieves R-2.5 to R-3.7 per inch and costs $1.00-$2.80 per square foot installed. Professional attic installation ranges from $1,800-$3,500, making it slightly more expensive than batts but superior for filling gaps around existing framing and electrical wiring. This method eliminates thermal bridging that occurs with batt installation.

2-4 hours professional blowing machinehoseprotective equipment

Pro tip: Blown-in fiberglass settles approximately 20% over time, so contractors typically over-fill by this amount to maintain target R-values. Request this in writing when getting quotes.

3. Blown-In Cellulose: Eco-Friendly with Sound Dampening

Cellulose insulation provides R-3.2 to R-3.8 per inch at $0.50-$1.00 per square foot, offering superior soundproofing compared to fiberglass. Made from 75-85% recycled newspaper, it costs $1,500-$3,000 professionally installed in a typical attic. The material's density provides 30% better noise reduction than fiberglass of equivalent thickness.

2-4 hours professional blowing equipmentprotective gear

Pro tip: Cellulose requires treatment with boric acid for fire resistance, so verify your contractor uses fire-rated material. Some regions have stricter fire codes that mandate this treatment.

4. Open-Cell Spray Foam: Flexible Air Sealing for Moderate Climates

Open-cell spray foam delivers R-3.5 to R-3.9 per inch and costs $1.50-$4.00 per square foot, with professional attic installation ranging $3,500-$7,000. This type is not DIY-friendly and requires licensed applicators. It provides superior air sealing compared to traditional batts and acts as a sound barrier, though it offers lower R-value per inch than closed-cell alternatives.

1-2 days professional spray equipmentprotective equipment

Pro tip: Open-cell foam is permeable to vapor, making it ideal for climates with seasonal humidity changes. It allows moisture to escape, preventing trapped condensation that can damage attic framing.

5. Closed-Cell Spray Foam: Maximum R-Value for Space-Constrained Areas

Closed-cell spray foam achieves R-5.6 to R-8.0 per inch—nearly double other options—at $3.50-$7.00 per square foot installed. Professional attic installation costs $5,500-$10,000, making it the most expensive option. A 2-inch application delivers R-11 to R-16, compared to R-7.2 for open-cell foam of the same thickness. This material doubles as both air and vapor barrier, eliminating the need for separate barriers.

1-2 days professional spray equipmentprotective equipment

Pro tip: Closed-cell foam adds structural rigidity to roof assemblies, allowing it to support part of the roof load. This property is especially valuable in low-clearance attics where depth limitations make other materials impractical.

6. Mineral Wool (Rockwool): Fire-Resistant and Sound-Dampening

Mineral wool delivers R-4.0 per inch at $0.80-$1.50 per square foot, with professional installation costs comparable to fiberglass. This material is inherently fire-resistant and provides superior soundproofing—approximately 40% better than fiberglass. It resists moisture absorption and doesn't require additional vapor barriers in most applications.

4-8 hours DIY or 2-4 hours professional utility knifemeasuring tapestaple gunsafety glassesrespirator

Pro tip: Mineral wool's fire-rating makes it ideal for areas near chimneys, furnaces, or electrical panels where building codes mandate fire-rated insulation. It maintains structural integrity even when exposed to high temperatures.

7. Rigid Foam Boards: High R-Value Per Inch for Basements and Exterior Walls

Rigid foam boards (polyiso, XPS, EPS) provide R-4.0 to R-6.5 per inch at $2.00-$4.00 per square foot for materials alone. Extruded polystyrene (XPS) costs $3-$6 per square foot, while polyisocyanurate (PIR) ranges $1.50-$8 per square foot. These boards excel in basement walls and exterior applications where minimal thickness is critical. A 1-inch rigid board achieves R-4 to R-6, versus R-2.2 to R-3.8 for fiberglass of the same thickness.

6-10 hours DIY utility knifecircular sawadhesivefastenersmeasuring tape

Pro tip: Rigid foam boards must be covered with fire-rated drywall (1/2-inch minimum) in interior applications to meet building codes. The foam itself is combustible, so never leave it exposed on finished walls.

Bonus Tip

Calculate Your Attic's R-Value Requirement Based on Climate Zone

The Department of Energy recommends R-38 to R-60 for attics depending on climate zone. For example, northern climates require R-49 to R-60, while southern climates need R-38 to R-49. Divide your target R-value by the material's R-value per inch to determine required depth. If your attic needs R-49 and you're using fiberglass batts at R-3.8 per inch, you'll need approximately 13 inches of insulation. Check your local building codes and utility company rebate programs—many offer 20-50% cost reductions for upgrading to recommended R-values.

What to Avoid

  • Mixing insulation types without understanding vapor barrier requirements. Combining fiberglass (which requires a vapor barrier) with open-cell foam (which is vapor-permeable) can trap moisture and cause mold growth. Always maintain consistent vapor barrier strategy throughout.
  • Ignoring local building codes and climate zone recommendations. Installing R-38 insulation in a northern climate requiring R-49 leaves your home underinsulated, resulting in 15-20% higher heating costs. Verify requirements with your local building department before purchasing materials.
  • Assuming DIY installation saves money on spray foam. Closed-cell and open-cell spray foam require specialized equipment and licensing in most jurisdictions. DIY attempts often result in improper application, voids in coverage, and failed air sealing—negating the material's primary advantage.
  • Neglecting to air-seal before installing insulation. Adding insulation without sealing air leaks around penetrations, electrical outlets, and ductwork reduces effectiveness by 10-30%. Perform air-sealing first, then install insulation for optimal energy performance.