Seasonal Thermostat Settings Guide — Optimal Temperatures for Savings

Seasonal Timeline

Winter (December – February): Heating Season

Winter is when thermostat settings have the highest financial impact. Each degree above 68°F adds approximately 3% to your heating bill — and most households set the thermostat higher than they need to.

  1. Set the daytime occupied temperature to 68°F

    68°F is the widely recommended balance point between comfort and efficiency. Most people are comfortable at 68°F with normal indoor clothing (long sleeves, socks). If 68°F feels cold, try adding a layer before raising the thermostat — a sweater adds roughly 4°F of perceived warmth. Moving from 72°F to 68°F saves approximately 12% on heating costs, or $150–$300 per winter in most climates.

    1 minute Free (saves money)

  2. Set the nighttime sleeping temperature to 62°F

    Most people sleep better in cooler temperatures (60–67°F per the Sleep Foundation). Setting back to 62°F during 8 sleeping hours saves roughly 6–8% on heating costs compared to maintaining 68°F. Use warmer bedding to compensate — a good comforter is far cheaper than heating the whole house to 68°F overnight. If you wake up cold, try 64°F as a starting point.

    1 minute Free (saves money)

  3. Set the away/unoccupied temperature to 60–62°F

    When nobody is home for 4+ hours, set back to 60–62°F. Don't go below 55°F — lower settings risk frozen pipes in exposed areas. The system recovers to 68°F in 30–60 minutes when you return (use 'smart recovery' on programmable thermostats to have the house at 68°F by the time you arrive). Every 8-hour setback period saves roughly 1% per degree of setback.

    1 minute Free (saves money)

  4. HEAT PUMP EXCEPTION: Limit setback to 2–3°F maximum

    Heat pumps recover from setbacks very slowly compared to furnaces. A large setback (8–10°F) triggers the electric auxiliary heat strips to help with recovery — and those strips cost 2–3x more per hour than the heat pump itself. With a heat pump, set night temperature to 65–66°F (not 62°F) and away temperature to 65°F. The small setback still saves energy without triggering the expensive backup heat. Smart thermostats with heat pump-specific algorithms handle this automatically.

    2 minutes Free

Spring (March – May): Transition Season

Spring temperatures swing between heating and cooling needs, sometimes in the same day. The goal is to minimize HVAC runtime by using the 'dead band' — the gap between heating and cooling setpoints where the system does nothing.

  1. Switch to auto changeover mode if your thermostat supports it

    Auto changeover lets the thermostat switch between heating and cooling as needed. Set the heating setpoint to 66°F and the cooling setpoint to 76°F. This creates a 10-degree dead band where the system stays off entirely — which on mild spring days might be all day. The wider the dead band, the less the system runs. Avoid setting heating and cooling setpoints within 4°F of each other, which causes unnecessary cycling.

    5 minutes Free

  2. Use windows and fans instead of HVAC on mild days

    When outdoor temperatures are between 55–75°F, open windows and use ceiling fans or a whole-house fan instead of running the HVAC system. Natural ventilation costs nothing and gives the system a rest. Close windows and switch back to HVAC when outdoor temperatures exceed 75°F or humidity rises above 60% — running the AC with windows open wastes energy and overworks the compressor.

    2 minutes Free

  3. Adjust your thermostat schedule for daylight saving time

    Daylight saving time shifts your daily routine by an hour, but many thermostat schedules don't update automatically. Smart thermostats adjust on their own; programmable thermostats need manual updates. If your schedule shows 'wake at 6 AM' but you now wake at 7 AM due to the time change, you're heating an empty house for an hour every morning.

    5 minutes Free

Summer (June – August): Cooling Season

Cooling is more expensive per degree than heating in most climates because air conditioners use electricity (at higher cost per BTU than natural gas). Every degree below 78°F adds approximately 3–4% to your cooling bill.

  1. Set the daytime occupied temperature to 78°F

    78°F is the DOE-recommended cooling setpoint. It feels comfortable when indoor humidity is controlled (which a properly functioning AC does). If 78°F feels warm initially, give it 3–5 days — your body acclimates. Pair with ceiling fans for a wind-chill effect that makes 78°F feel like 74°F. Moving from 72°F to 78°F saves roughly 18–24% on cooling costs.

    1 minute Free (saves money)

  2. Set the away temperature to 85°F — not 'off'

    Turning the AC completely off while away lets the house reach 95°F+ and humidity rises unchecked. Recovery takes hours, uses more energy than maintaining a moderate setback, and the humidity spike can promote mold growth. Set to 85°F when away for 4+ hours — the system barely runs but keeps humidity and temperature from reaching extremes.

    1 minute Free (saves money)

  3. Set the fan to AUTO, not ON

    The 'ON' setting runs the blower fan continuously, even when the AC compressor is off. This uses 200–500 watts 24/7 ($15–$40/month) and — critically — re-evaporates moisture that collected on the evaporator coil during the cooling cycle, pushing humidity back into the house. The 'AUTO' setting runs the fan only during cooling cycles, which is more efficient and better for humidity control in summer.

    1 minute Free (saves money)

  4. Use ceiling fans to extend your comfort range by 4°F

    Set ceiling fans to counterclockwise (downdraft direction) at medium speed. The wind-chill effect makes 78°F feel like 74°F to occupied rooms. A ceiling fan uses 15–75 watts vs. 2,000–5,000 watts for the AC compressor. But remember: fans cool people, not rooms. Turn fans off when you leave the room — a fan running in an empty room wastes energy with zero comfort benefit.

    2 minutes Free

Fall (September – November): Transition Back to Heating

Fall mirrors spring: temperature swings, mixed heating and cooling days, and the opportunity to minimize HVAC runtime before the furnace takes over full-time.

  1. Return to auto changeover mode with a wide dead band

    Same strategy as spring: set heating to 66°F and cooling to 76°F. On mild fall days (common in September and October), the system stays off entirely. As nights get cooler, you'll notice the furnace kicking on in the early morning — that's normal. Resist the urge to raise the heating setpoint to avoid the brief morning chill; it passes in 30 minutes as the house absorbs daytime heat.

    5 minutes Free

  2. Switch to heating-only mode when daily highs stay below 65°F

    Once daytime temperatures consistently stay below 65°F, there's no need for cooling. Switch the thermostat from auto changeover to heat-only mode. Set daytime to 68°F, nighttime to 62°F (or 65–66°F for heat pumps), and away to 60–62°F. This is your winter configuration.

    2 minutes Free

  3. Verify your thermostat schedule matches your fall routine

    If your work or school schedule changes in fall, update the thermostat to match. Kids back in school means an empty house during the day — take advantage of the setback. End of daylight saving time in November shifts sunrise/sunset — adjust the schedule so the house is warm when you wake up, not an hour earlier. Smart thermostats learn these patterns; programmable thermostats need manual updates.

    5 minutes Free

Quick Reference Calendar

MonthTasksPeriod
January 0 tasks
February 4 tasks Winter (December – February): Heating Season
March 3 tasks Spring (March – May): Transition Season
April 0 tasks
May 3 tasks Spring (March – May): Transition Season
June 4 tasks Summer (June – August): Cooling Season
July 0 tasks
August 4 tasks Summer (June – August): Cooling Season
September 3 tasks Fall (September – November): Transition Back to Heating
October 0 tasks
November 3 tasks Fall (September – November): Transition Back to Heating
December 4 tasks Winter (December – February): Heating Season

Pro Tips

  • The 1-Degree Rule: Each Degree Is Worth About 3%

    In both heating and cooling, each degree of setpoint change saves approximately 1–3% on that season's energy costs. This is the single most useful number for making thermostat decisions. Want to save $200 this winter? Drop the thermostat 4 degrees and put on a sweater. Want to save $150 this summer? Raise it 4 degrees and use ceiling fans.

    Best time: All year

  • Smart Thermostats Pay for Themselves in One Year

    A smart thermostat ($100–$250) learns your schedule, adjusts for occupancy, and optimizes recovery timing. The Nest and Ecobee both claim 10–15% savings, which means a $150–$300 annual return on a one-time investment. Many utility companies offer $50–$100 rebates that bring the payback period to under 6 months. The biggest advantage: smart thermostats actually get used as programmed, unlike programmable thermostats that 40% of owners never program.

    Best time: Before heating or cooling season

  • Don't Crank the Thermostat to Heat or Cool Faster

    Setting the thermostat to 85°F doesn't heat the house faster than setting it to 68°F — the furnace runs at the same output regardless. All you accomplish is overshooting the target and wasting energy. The same applies to cooling: setting the thermostat to 60°F doesn't cool faster, it just runs the AC longer than needed. Set the target temperature and let the system reach it at its own pace.

    Best time: All year