Seasonal Timeline
September: Basic Prep and Professional Scheduling
September is for the easy wins and advance planning. Temperatures are still mild, so there's no urgency — use that to your advantage by booking professional service before the fall rush.
-
Replace the furnace filter with a fresh one
Start the heating season with a clean filter. If the old filter has been sitting since spring, it's accumulated summer dust, pollen, and humidity-related buildup even though the furnace wasn't running. Install a new pleated filter (MERV 8–11) and write the installation date on the filter frame so you know when to check it next.
-
Clear the area around the furnace — 3 feet of clearance on all sides
Over summer, furnace rooms tend to accumulate stored items. Boxes, paint cans, cleaning supplies, and holiday decorations encroach on the required clearance zone. Combustible materials near a furnace are a fire hazard, and blocked access panels prevent proper maintenance. Clear everything within 3 feet and keep it clear all winter.
-
Schedule a professional furnace tune-up for late September or October
Book now while schedules are open. By mid-October, most HVAC companies are backlogged with emergency calls. A fall tune-up costs $100–$200 and includes burner cleaning, flame sensor inspection, combustion analysis, heat exchanger check, and safety control testing. This annual service is the best money you'll spend on your furnace.
October: Professional Service and Safety Checks
October is the action month. Your professional tune-up should happen now, and you should complete all safety verifications before you need the furnace daily.
-
Complete the professional furnace tune-up
During the tune-up, the technician should: clean the burner assembly, test the flame sensor, check gas pressure, perform combustion analysis, inspect the heat exchanger for cracks, test all safety controls (high-limit switch, pressure switches, rollout switches), verify the ignition sequence, and check the blower motor and capacitor. Ask for a written report of findings.
-
Test all carbon monoxide detectors and replace batteries
Before the furnace runs regularly, verify your CO detection is working. Press the test button on every detector. Replace batteries even if they test fine — alkaline batteries lose capacity in cold temperatures, exactly when you need them most. Replace any detector over 5–7 years old regardless of battery status.
-
Program the thermostat with your winter heating schedule
Set your winter schedule: occupied temperature (68°F is the sweet spot for comfort and efficiency), unoccupied setback (60–62°F saves 10–15% on heating bills), and wake/sleep transitions. If you have a smart thermostat, fall is a good time to verify it's connected to Wi-Fi and update its software. Enable the 'heating season' or 'winter' mode if available.
-
Run the furnace through a full heating cycle and check every room
Set the thermostat to heat and 5 degrees above room temperature. Wait for the furnace to start and run through a complete cycle. Walk to every supply register and verify airflow. Check for unusual smells — a brief dusty smell is normal on the first run, but any burning plastic, rotten egg (gas leak), or persistent musty odor requires immediate investigation.
November: Final Checks and Emergency Preparedness
By November, your furnace should be professionally serviced and tested. These final steps ensure you're prepared for the coldest months and any unexpected failures.
-
Check the furnace filter again — the first month of use is the dirtiest
If you installed a fresh filter in September, check it in November after the first month of regular heating. The initial startup stirs up dust that's settled in ductwork over summer. If the filter is already heavily loaded, replace it and check again in 30 days to establish your actual replacement interval for this heating season.
-
Inspect the condensate drain on high-efficiency furnaces
High-efficiency condensing furnaces (90%+ AFUE) produce several gallons of condensate daily during heavy operation. The drain line can clog with algae, mineral deposits, or debris, causing water backup and furnace shutdown. Pour a cup of water into the condensate trap to verify it drains freely. Flush the drain line with a mixture of warm water and vinegar.
-
Prepare a backup heating plan in case of furnace failure
Have a plan for the worst case: furnace failure during a deep freeze. Keep a portable electric space heater rated for indoor use. Know where your gas shutoff valve is. Have your HVAC contractor's emergency number saved in your phone — not just on a sticker on the furnace. If you rely on a generator, test it now and store fuel safely.
Quick Reference Calendar
| Month | Tasks | Period |
|---|---|---|
| January | 0 tasks | |
| February | 0 tasks | |
| March | 0 tasks | |
| April | 0 tasks | |
| May | 0 tasks | |
| June | 0 tasks | |
| July | 0 tasks | |
| August | 0 tasks | |
| September | 3 tasks | September: Basic Prep and Professional Scheduling |
| October | 4 tasks | October: Professional Service and Safety Checks |
| November | 3 tasks | November: Final Checks and Emergency Preparedness |
| December | 0 tasks |
Pro Tips
-
The First-Run Smell Test
A brief dusty or 'hot metal' smell when the furnace first fires in fall is normal — it's dust burning off the heat exchanger. It should disappear within 30 minutes. If you smell rotten eggs, shut off the furnace and gas supply immediately — that's a gas leak. If you smell burning plastic, shut off the furnace and inspect for melted wiring or debris on the heat exchanger.
-
Save Money With the 68°F Rule
Every degree above 68°F adds approximately 3% to your heating bill. Setting the thermostat to 72°F instead of 68°F costs roughly 12% more for the season. Wear a sweater, use blankets, and keep the thermostat at 68°F during the day and 60–62°F at night or when away.
-
Don't Close Vents to 'Save Energy'
Closing supply vents in unused rooms seems logical but actually increases duct pressure, forces more air through leaks, and can cause the furnace to short-cycle. Modern furnaces are sized and balanced for the whole house. If you want zone control, talk to your HVAC contractor about a zoning system with dampers — not closed vents.