8 Things to Do When Your Water Heater Starts Leaking (2026)

1. Turn off the power supply to the water heater

Before touching anything else, cut the energy source. For electric water heaters, flip the dedicated breaker in your electrical panel — it is usually a double-pole 30-amp breaker labeled 'water heater' or 'WH'. For gas water heaters, turn the gas control knob on the unit to the 'Off' position. Water and electricity or gas are both dangerous combinations, and the heater's heating elements can burn out or create a fire hazard if the tank runs dry while powered.

1–2 minutes

Pro tip: If your breaker panel is not labeled, look for the largest double breaker that is not the main. Water heaters typically draw 4,500 watts — they need a dedicated 30-amp circuit.

2. Shut off the cold water supply valve above the heater

The cold-water inlet valve sits on top of or just above the water heater on the supply line. Turn it clockwise to close. This stops fresh water from entering the tank and feeding the leak. If the valve is stuck or broken — common on older units — shut off your home's main water valve instead. A 50-gallon tank refilling while leaking can dump hundreds of gallons in a few hours.

1 minute

Pro tip: Test your water heater's inlet valve once a year — turn it off and on. Valves that sit untouched for years seize up and will not close when you actually need them.

3. Identify where the water is actually coming from

Not all water around a water heater is a tank leak. Check these common sources first: condensation on cold pipes (harmless), the T&P (temperature and pressure) relief valve or its discharge tube, loose supply line fittings, the drain valve at the bottom, or a nearby appliance. Wipe the heater dry and lay paper towels around the base and connections. Wait 30 minutes and check which towels are wet. A fitting or valve can often be repaired. HomeGuide says a leaking tank itself usually means replacing the heater, at $600 to $1,800.

30 minutes

Pro tip: A.O. Smith says a leaking T&P valve can be caused by high pressure or thermal expansion. Have a plumber find the cause. Never cap, plug, or remove the valve or its discharge pipe, and stay clear of the discharge pipe, because the water can be scalding.

4. Drain the tank if the leak is significant

If water is actively pooling, attach a garden hose to the drain valve at the bottom of the tank and run it to a floor drain, sump pit, or outside. Open the drain valve and open a hot water faucet upstairs to break the vacuum and let the tank drain. A full 50-gallon tank weighs over 400 pounds — draining it reduces flood risk and makes the unit manageable for the plumber.

20–45 minutes to drain

Pro tip: The water coming out will be hot — potentially scalding. Run the hose to a safe drain location and keep children and pets away from the discharge point.

5. Check for water damage to nearby walls, flooring, and belongings

Water heaters are usually in basements, garages, or utility closets near stored items. Check behind and under the heater for water that has spread to drywall, cardboard boxes, or finished flooring. Move anything stored within 4 feet of the heater. Water damage to drywall and flooring that goes unnoticed for even 24 hours creates mold conditions that cost thousands to remediate.

10 minutes

Pro tip: Shine a flashlight along the base of nearby walls. Water migrating behind baseboards is invisible from above but shows as a dark line where the drywall meets the floor.

6. Document the leak and damage for insurance

If the leak has caused water damage beyond the heater itself, your homeowner's insurance may cover it — most policies cover sudden water heater failures but not slow leaks from maintenance neglect. Photograph the leaking heater, the manufacturer label (with model and serial number), the water damage, and any damaged belongings. Note the date and time you discovered the leak. File a claim before authorizing a replacement if the damage is significant.

10 minutes

Pro tip: Photograph the data plate on your water heater — it shows manufacture date, model, and serial number. Adjusters use this to determine the age and whether neglect contributed to the failure.

7. Decide repair versus replacement based on the heater's age

HomeGuide puts tank water heater life at 8 to 15 years. If yours is leaking from the tank body (not a fitting or valve), internal corrosion has broken through the steel and it cannot be patched permanently. HomeGuide notes that leaking tanks typically require replacement ($600 to $1,800). Repairing a valve or fitting on a younger heater makes sense. HomeGuide lists average tank repairs at $150 to $700.

5 minutes to check age

Pro tip: The manufacture date is usually encoded in the serial number on the data plate, but each brand uses a different format. Search for your brand's serial-number date code, or ask the plumber to read it.

8. Call a licensed plumber — not a handyman or a big-box store installer

Water heater replacement involves gas lines or high-voltage electrical, water supply connections, venting (for gas units), expansion tanks (required by code in many areas), and seismic strapping (in earthquake zones). Code requirements change frequently and vary by jurisdiction. Licensed plumbers know current code and pull permits. Big-box store subcontractors and handymen often skip permits, expansion tanks, and proper venting — all of which create safety and insurance problems.

10 minutes to call

Pro tip: Ask the plumber whether your local code requires a thermal expansion tank. A.O. Smith links T&P valve leaks to high pressure and thermal expansion, so an expansion tank or pressure-reducing valve may be part of the fix.

Bonus Tip

Consider upgrading to a tankless water heater while you are replacing

If the tank has failed and you are replacing it anyway, this is the natural time to weigh tankless. HomeGuide lists new tankless installation at $1,400 to $5,600, with tankless units lasting 10 to 20 years compared with 8 to 15 for tanks. Tankless heaters need regular flushing ($150 to $350, more often with hard water), so include that in the comparison.

What to Avoid

  • Ignoring a small drip because it seems minor. A pinhole tank leak is corrosion that only gets worse, and water damage behind a wall can go unnoticed for weeks.
  • Trying to weld, epoxy, or patch a leaking tank. HomeGuide notes leaking tanks typically require replacement.
  • Capping or plugging the T&P relief valve or its discharge pipe.
  • Skipping the permit for a water heater replacement where one is required. Unpermitted work can cause problems with insurance and when selling your home.
  • Letting an unqualified installer handle gas connections and venting. A bad vent can spill carbon monoxide into the house.