8 Things to Do If Your GFCI Won’t Reset (2026)

1. Unplug everything connected to the GFCI and its downstream outlets

A GFCI protects not just itself but all outlets wired downstream of it — often 2–4 additional outlets in the same room or adjacent rooms. A ground fault in any device plugged into any of these outlets will prevent the GFCI from resetting. Unplug every device from the GFCI outlet and all other dead outlets, then try the reset button again. If it resets, plug devices back in one at a time to identify the faulty appliance.

5 minutes

Pro tip: The most common culprit is a bathroom hair dryer, curling iron, or kitchen countertop appliance with worn insulation. If the GFCI resets after unplugging one specific device, that device has a ground fault and should be replaced.

2. Check whether the GFCI has power reaching it

A GFCI can't reset if it's not receiving power. Check the breaker panel — the breaker feeding the GFCI circuit may be tripped. Also check whether a different GFCI upstream is tripped. In some wiring configurations, one GFCI feeds another, and the upstream GFCI must be reset first. Walk through the house and press the reset button on every other GFCI you can find.

5–10 minutes

Pro tip: GFCIs in garages and exterior outlets are commonly wired upstream of bathroom or kitchen GFCIs. If your bathroom outlet won't reset, check the garage and outdoor outlets first.

3. Press the reset button firmly and fully — a weak push won't engage

The GFCI reset mechanism requires a firm, decisive push until you hear a distinct click. Many homeowners press too gently, especially on older units where the button has stiffened from disuse. Press with your thumb directly centered on the button until it clicks and the button stays recessed. If it pops back out immediately, the GFCI is still sensing a fault.

10 seconds

Pro tip: If the button feels mushy, doesn't click, or won't stay pressed in, the GFCI's internal mechanism may have failed. Buttons that won't engage mechanically indicate a unit that needs replacement regardless of other troubleshooting.

4. Test whether the issue is a tripped GFCI or a dead GFCI

A tripped GFCI still has power reaching it — the trip mechanism just disconnected the output. A dead GFCI has no power at all. Use a non-contact voltage tester on the face of the GFCI. If it detects voltage, the unit is tripped. If it detects nothing, power isn't reaching the outlet — check the breaker and upstream GFCIs. This distinction determines whether you're troubleshooting a fault or a power supply issue.

2 minutes

Pro tip: Test on the small slot (hot side) of the GFCI face. Non-contact testers detect the hot conductor through the plastic, confirming whether the line side of the GFCI is energized.

5. Look for moisture inside the outlet box

GFCIs in bathrooms, kitchens, garages, and exterior locations are exposed to humidity and splashing. If moisture enters the outlet box — from a leaking pipe, condensation, or an improperly sealed exterior box — the GFCI will sense a ground fault and refuse to reset because a real ground fault exists. Turn off the breaker, remove the GFCI cover plate, and look for visible moisture, corrosion, or water staining.

10 minutes

Pro tip: Exterior GFCI outlets must be in a weatherproof in-use cover (the bubble-style cover that seals while a cord is plugged in). A flat cover plate exposes the outlet to rain every time something is plugged in.

6. Check if the GFCI is at end of life

GFCIs have a lifespan of 10–15 years, after which the internal sensing circuitry degrades and the unit may fail in an unsafe manner — either refusing to reset (safe failure) or failing to trip on a ground fault (dangerous failure). If your GFCI is older than 10 years, replace it regardless of whether you can get it to reset. A new GFCI costs $15–$25 and takes 15 minutes to install.

Check installation date on unit

Pro tip: Since 2015, the NEC requires self-testing GFCIs that automatically check their own trip mechanism every few minutes. Older units don't have this feature — upgrading to a self-testing GFCI gives you passive protection monitoring.

7. Test the GFCI after resetting to confirm it's actually protecting you

Getting the GFCI to reset is only half the job. After a successful reset, press the test button. The GFCI should click and the outlet should go dead — this confirms the trip mechanism works. If pressing test doesn't kill power, the GFCI has failed in a dangerous way: it's passing power without providing ground fault protection. Replace it immediately.

10 seconds

Pro tip: Use a plug-in GFCI tester ($12–$15) for a more thorough test than the built-in button. Plug-in testers create an actual ground fault and verify the GFCI trips at the correct threshold (4–6 milliamps).

8. Call an electrician if the GFCI won't reset after you've eliminated all plugged-in devices

If the GFCI refuses to reset with nothing plugged in and power confirmed at the breaker, the ground fault is in the building wiring itself — not an appliance. Common causes include a damaged wire in the wall, a nail or screw that penetrated cable insulation, rodent damage to wire sheathing, or a deteriorated wire splice in an inaccessible junction box. These require an electrician with insulation resistance testing equipment.

Schedule electrician

Pro tip: Tell the electrician that you've already isolated the fault to the building wiring by unplugging all devices. This lets them skip basic troubleshooting and go directly to insulation resistance testing, saving you diagnostic labor time.

Bonus Tip

Map your GFCI protection zones

Spend 15 minutes pressing the test button on each GFCI in your home and checking which outlets throughout the house go dead. Write this map inside your panel door. When a GFCI trips in the future, you'll immediately know which outlets are affected and where to look for the faulty device. Most homeowners are surprised by how many outlets are protected by a single GFCI they rarely think about.

What to Avoid

  • Replacing a GFCI that won't reset with a standard outlet to 'solve' the problem — the GFCI is refusing to reset because a real hazard exists on that circuit.
  • Using a GFCI that's older than 15 years without testing it monthly — older GFCIs have a high failure rate and may be providing no protection at all.
  • Ignoring a bathroom GFCI that trips frequently — frequent trips near water mean an appliance or the wiring has a developing ground fault that worsens over time.
  • Wiring a replacement GFCI with the line and load terminals reversed — this powers the outlet but eliminates ground fault protection for downstream outlets.