8 Things to Do If You Find Missing Flashing After High Winds (2026)

1. Identify what type of flashing is missing

Roof flashing comes in several types—step flashing (along walls), counter flashing (embedded in masonry), valley flashing (where two slopes meet), and drip edge (along eaves and rakes). Each type protects a different vulnerable joint, and the urgency depends on which one is gone. Missing valley flashing is the most critical because valleys channel the heaviest water flow. Missing drip edge is less immediately dangerous but will cause fascia rot within weeks if not addressed.

10–20 minutes

Pro tip: Use binoculars from the ground rather than climbing up. Missing flashing is usually visible as a gap of bare wood or exposed underlayment where you'd expect to see a thin metal strip. Take photos from multiple angles.

2. Check the ground and gutters for the displaced flashing pieces

Wind-displaced flashing often lands in the yard, on a lower roof section, or lodges in the gutters. Finding the actual pieces helps your insurance claim because it proves the damage was wind-caused rather than a maintenance failure. Collect any metal pieces you find, photograph them where they landed before moving them, and store them for the adjuster. The metal type and condition also tells your roofer whether the original installation was done correctly.

15–30 minutes

Pro tip: If the flashing pieces show clean separation at the nail line, wind tore them free. If the metal is corroded and crumbling at the edges, it was already failing—and your insurer may classify it as wear rather than storm damage.

3. Apply a temporary waterproof seal to the exposed joint

The gap left by missing flashing is a direct path for water into your roof deck, walls, or attic. For a temporary fix, apply roofing cement or a self-adhesive flashing tape (like Flex Seal tape or Grace Vycor) over the exposed area. This buys you 2–4 weeks of protection depending on weather. The temporary fix typically costs $15–$40 in materials versus the $1,500–$5,000 in water damage that an unprotected joint can cause in a single heavy rain.

30–60 minutes

Pro tip: Butyl-based tapes outperform asphalt-based products for temporary repairs. They stay flexible in cold weather and don't crack in heat, giving you a more reliable seal until the professional repair.

How to do it:

  1. Wait until the roof surface is completely dry—adhesives won't bond to wet surfaces.
  2. Clean loose debris and old sealant from the exposed joint using a stiff brush.
  3. Apply roofing cement generously over the gap, extending at least 3 inches past the edge on all sides.
  4. Press self-adhesive flashing tape firmly over the cement for a secondary seal.
  5. Smooth the edges to prevent wind from catching and peeling the tape.

4. Photograph and document the damage for insurance

Flashing damage is one of the most under-documented and under-claimed roof issues. Take close-up photos showing the exposed joint, the area where the flashing was attached (look for nail holes or sealant residue), and any collected flashing pieces. Include a wide shot showing the flashing location relative to the overall roof. Note the date and time of the storm that caused the damage—weather records can corroborate your timeline if the insurer questions it.

15–20 minutes

Pro tip: Check NOAA's storm event database for your county and date. A recorded wind event of 58+ mph is classified as severe and is strong evidence that the flashing loss was storm-caused, not wear-related.

5. Inspect the interior wall and ceiling beneath the missing flashing

Water entering through a flashing gap doesn't just damage the roof—it runs down inside walls, soaking insulation, staining drywall, and potentially reaching electrical wiring. Check the interior wall and ceiling directly below the missing flashing for dampness, discoloration, or a musty smell. If the flashing was at a wall-to-roof junction, also check the wall cavity by feeling for soft spots. Interior damage significantly increases your claim value and urgency.

15–20 minutes

Pro tip: A $25 pin-type moisture meter from any hardware store can detect hidden moisture in drywall and wood. Readings above 17% indicate active moisture intrusion that isn't visible on the surface yet.

6. File your insurance claim and specify the flashing by type and location

When calling your insurer, don't just say "flashing is missing." Specify the type (step, counter, valley, or drip edge), the exact location (e.g., "north-facing chimney step flashing"), and the approximate linear footage affected. Detailed initial reports result in more accurate first inspections. Flashing replacement costs range from $200–$500 for a simple drip edge run to $1,500–$3,000 for chimney counter flashing, so precise identification prevents underestimation.

20–30 minutes

Pro tip: Request that the adjuster inspect the flashing damage from the roof—not just from the ground or via photos. Ground-level assessments routinely underestimate flashing damage because the affected joints are often hidden from below.

7. Get a professional roofer to assess whether adjacent materials are compromised

When wind tears flashing loose, it often lifts or cracks the surrounding shingles, damages the underlayment, or pulls nails from the decking. A roofer should inspect not just the flashing gap but the 3–5 foot zone around it for collateral damage. Missing step flashing along a dormer wall, for example, frequently means the shingles that overlapped the flashing are also compromised. This adjacent damage can double the repair scope and should be included in your claim.

30–45 minutes for inspection

Pro tip: If the roofer finds that the underlayment beneath the missing flashing is torn or deteriorated, the repair must include underlayment replacement—not just new flashing. This is commonly missed by adjusters but adds $200–$600 to the approved scope.

How to do it:

  1. Contact at least two licensed roofers who have experience with insurance claims.
  2. Ask them to inspect both the flashing gap and a 5-foot radius around it for collateral damage.
  3. Request a written report noting all damaged components, not just the flashing.
  4. Share the report with your insurance adjuster to ensure the full scope is documented.

8. Check other flashing points on the roof for loosening

Wind damage is rarely isolated to one spot. If one section of flashing was torn off, other flashing points on the same roof are likely loosened or lifted, even if they haven't fully detached yet. A loose flashing that's still in place may look fine from the ground but will fail in the next storm. Ask your roofer to test all flashing points during their inspection by gently pressing on them—properly secured flashing should not flex or lift.

Included in professional inspection

Pro tip: Pay special attention to flashing around plumbing vent boots—they're the most common failure point on any roof and are often made of rubber that degrades in UV exposure. A cracked vent boot costs $15 to replace proactively and $2,000+ if it leaks unnoticed.

Bonus Tip

Upgrade to a more wind-resistant flashing system during repair

If your original flashing was face-nailed aluminum (common in older homes), ask your roofer about upgrading to concealed-fastener galvanized steel or copper flashing during the repair. The material cost difference is $50–$150, but the wind resistance improvement is substantial. This upgrade may be covered by your insurance if current building code requires it in your jurisdiction.

What to Avoid

  • Do not use silicone caulk as a permanent flashing replacement—it deteriorates within 1–2 years in direct sun and creates a false sense of security while water seeps behind it.
  • Do not climb onto a wet or wind-damaged roof yourself; loose flashing can leave sharp metal edges and compromised decking that may not support your weight.
  • Do not delay the temporary seal because you're waiting for an adjuster—water damage from one storm can cost more than the entire flashing repair, and insurers expect you to mitigate.
  • Do not let a roofer install new flashing over old sealant or damaged underlayment; the new flashing will fail prematurely if the substrate beneath it is compromised.