8 Things to Do If Half Your House Loses Power (2026)

1. Check whether it's exactly half your circuits or random ones

Your home's 240-volt service enters on two 'legs' of 120 volts each. If you lose exactly one leg, every other breaker in your panel goes dead — a specific pattern. If random circuits are out, it's more likely a tripped main breaker or loose connection. Walk through every room and note which outlets and lights work. This pattern is the single most useful piece of information for your electrician.

10 minutes

Pro tip: Plug a phone charger into outlets in every room and note which charge and which don't. This creates a quick circuit map your electrician can use immediately.

2. Look at your 240-volt appliances — they'll tell you a lot

Your dryer, oven, water heater, and HVAC run on 240 volts, using both legs. If you've lost one leg, these appliances will behave strangely: the dryer may spin but not heat, the oven display may work but not reach temperature, or the AC may hum but not cool. If all 240-volt appliances are fully dead, both legs are down — likely a main breaker issue or utility outage.

5 minutes

Pro tip: Don't run 240-volt appliances on partial power. A motor receiving half its rated voltage draws excessive current to compensate and can burn out.

3. Check for a tripped main breaker at the top of your panel

Open your breaker panel door and look at the large breaker at the top (the main). If it's in the middle position — not fully on or off — it has tripped. Turn it all the way off first, then back on. If it trips again immediately, don't force it — there's a fault on the main line that needs an electrician.

2 minutes

Pro tip: The main breaker can appear to be in the ON position but still be tripped internally. Push it firmly to OFF until it clicks, then back to ON. This clears a partial trip that may not be visible.

4. Check your neighbors — this might be a utility problem, not yours

A downed transformer, a broken connection at the pole, or a damaged utility line can drop one leg of power to your house while keeping the other live. Ask neighbors on both sides whether they have full power. If they're also experiencing partial outages, call the utility company — the problem is on their equipment and they'll fix it at no charge.

5 minutes

Pro tip: Check the utility company's outage map on their website before calling. Many utilities now show real-time outage areas, and you can report your outage online faster than waiting on hold.

5. Inspect your meter base for visible damage

Your electric meter sits in a gray box on the exterior of your house. Look for burn marks, melted plastic, a crooked or loose meter, or water inside the meter box. A corroded or damaged connection at the meter base is one of the most common causes of partial power loss — and it's the utility's responsibility to repair since they own the meter.

2 minutes

Pro tip: Do not open the meter box or touch the meter. The connections inside carry live utility power with no breaker protection. Just look through the glass or plastic cover for obvious damage.

6. Turn off sensitive electronics immediately

Partial power loss can cause voltage fluctuations on the circuits that are still live. Circuits that normally receive 120 volts may receive unstable voltage that swings between 90 and 140 volts. This destroys computer power supplies, TV mainboards, and refrigerator compressor motors. Unplug computers, TVs, and your refrigerator until full power is restored.

5 minutes

Pro tip: If you have a UPS (uninterruptible power supply) on your computer, check its display — most UPS units show the incoming voltage. Anything below 110V or above 125V during the partial outage confirms unstable power on the live leg.

7. Don't run your generator without a transfer switch

If half your house is dark and you connect a portable generator by backfeeding through an outlet, you're sending power back through your panel onto the utility grid. This creates lethal voltage on the downed utility line that a lineworker may be trying to repair. It's also illegal in every state. Use a generator only with a proper transfer switch, or run extension cords directly from the generator to individual appliances.

N/A

Pro tip: A manual transfer switch costs $300–$500 installed and lets you safely power critical circuits from a generator during any outage. It's a one-time investment that pays off every storm season.

8. Call an electrician if it's not a utility issue — and describe what you've found

If your neighbors have full power and your utility confirms no outage, the problem is between your meter and your panel. Tell the electrician exactly what you found: which circuits are dead, whether 240-volt appliances work, and whether you see any damage at the panel or meter. This lets them bring the right parts and diagnose faster, saving you diagnostic labor charges.

10 minutes

Pro tip: Ask the electrician if they can test the voltage at your panel remotely by having you read the main breaker amperage rating. Some problems — like a lost neutral — have predictable symptoms that an experienced electrician can diagnose over the phone.

Bonus Tip

Keep a voltage tester in your toolkit

A non-contact voltage tester ($15–$25) lets you check whether any outlet is live without touching a wire. Hold it near the outlet and it beeps if voltage is present. During a partial outage, you can map your dead circuits in 5 minutes instead of plugging in a lamp in every room. It's also useful for confirming a breaker is truly off before working near an outlet.

What to Avoid

  • Opening your main electrical panel cover to inspect wiring — the bus bars are energized at 240 volts even during a partial outage and can deliver a fatal shock.
  • Backfeeding a generator through a dryer outlet or any house outlet — this sends power back onto utility lines and can kill a lineworker.
  • Ignoring a partial outage overnight thinking it will fix itself — if the cause is a loose connection or damaged wire, it can overheat and start a fire.
  • Turning on all your breakers at once after power is restored — re-energize circuits one at a time with a 30-second gap to avoid an inrush surge.