7 Ventilation Hood Types and Sizing Rules (2026 Guide)

1. Under-Cabinet Hoods Match Ranges with 3-Inch Overhang

Under-cabinet hoods install beneath cabinets and require a width at least equal to the range plus 3 inches on each side, so a 30-inch range needs a 36-inch hood costing $200-$800. Minimum CFM is 100, with most models at 150-350 CFM for effective smoke capture. They support both ducted and recirculating setups, but ducted versions vent outside per code.

1-2 hours ScrewdriverDrillDuct tape

Pro tip: Opt for models with flexible exhaust interfaces supporting 6-10 inch round or rectangular ducts to cut installation friction by 30% and noise.

2. Wall-Mounted Chimney Hoods Need 30-36 Inch Clearance

Wall-mounted chimney hoods, priced $500-$2,500, mount on walls above ranges and demand 30-36 inches clearance over gas cooktops to avoid scorching. Size hood width to range plus 3 inches per side for 6-inch total overhang, enhancing capture efficiency by 25%. CFM should hit BTU/100 for gas ranges, typically 300-600 CFM.

3-4 hours LevelStud finderDuct connector

Pro tip: Use stainless steel construction at least 0.0335 inches thick for durability, as it resists grease buildup 40% better than painted finishes.

3. Island Canopy Hoods Require 20% Extra CFM

Island canopy hoods suspend from ceilings over island ranges, costing $800-$4,000, and need 20% more CFM than wall models due to open airflow, often 400-900 CFM. Width must match range plus 3 inches per side; for 36-inch ranges, choose 42-48 inches. They mandate exterior venting with 6-10 inch ducts.

4-6 hours Ceiling joist finderHeavy-duty ladderDuct supports

Pro tip: Position at exactly 30-36 inches above cooktop; every inch higher reduces suction efficiency by 10%, per 2026 ventilation tests.

4. Ductless Recirculating Hoods Use Carbon Filters

Ductless hoods, $150-$600, recirculate air through carbon filters capturing 70% of odors and smoke without exterior venting, allowed only if code-listed. Size to range width plus 3 inches overhang; 100 CFM minimum suits light cooking. Filters cost $20-$50 to replace every 6 months.

30 minutes ScrewdriverTape measure

Pro tip: Pair with 150 CFM models for electric cooktops; they reduce noise to under 3 sones, 50% quieter than ducted equivalents.

5. Vented Ducted Hoods Limit Duct to 18 Feet Max

Vented hoods exhaust outside via ducts up to 18 feet for 200 CFM with 6-inch smooth diameter, priced $400-$3,000. For gas, CFM equals BTU/100; a 50,000 BTU range needs 500 CFM. Codes prohibit attic venting, requiring straight runs with minimal elbows.

2-3 hours Duct cutterFoam sealantWire crimper

Pro tip: Use 8-inch rigid ducts for 400+ CFM to avoid 20% backpressure loss; flex ducts drop efficiency by 15% per code charts.

6. Insert Hoods Fit Custom Canopies at Exact Widths

Insert hoods, $300-$1,500, slide into custom wood or metal canopies matching 36-inch vent models minimum, per manufacturer specs. Overhang 3 inches per side over ranges; 150-350 CFM standard. Depth typically 22 inches for optimal grease capture.

5-7 hours Reciprocating sawCustom canopy kitElectrical tester

Pro tip: Verify grain direction vertical on wood canopies for 15-7/8 inch base fit; mismatches cause 10% airflow restriction.

7. Downdraft Hoods Size for Slide-In Ranges Only

Downdraft hoods rise from cooktops at $200-$1,200, ideal for slide-ins without overhead space, but capture only 50% of smoke versus 90% for overhead. CFM 300-600 with 6-inch ducts; width matches range exactly, no overhang needed. Best for induction, less effective on gas.

1 hour Voltage testerPVC cement

Pro tip: Boost to 400 CFM for gas; codes in 46 states require 100 CFM minimum, but downdrafts need makeup air over 400 CFM.

Bonus Tip

Calculate CFM with Room Formula for Perfect Sizing

Multiply kitchen length x width x height then divide by 4 for base CFM; a 10x12x8 foot room needs 240 CFM minimum. Add 100 CFM per gas burner over 4 for precision. Test post-install with smoke to verify 80%+ capture rate.

What to Avoid

  • Undersizing width: Hoods narrower than range miss 30% of smoke; always add 3 inches per side for $0 extra efficiency gain.
  • Exceeding duct length: Over 18 feet for 200 CFM drops CFM by 25%; use code charts for diameter-specific maxes.
  • Skipping exterior vent: Ductless only for light use; vented removes 90% pollutants versus 50% recirculating.
  • Ignoring clearance: Below 30 inches risks fire; above 36 inches loses 10% suction per inch.