7 Types of Pipe Materials and When to Use Each (2026 Guide)

1. Copper Pipes: The Gold Standard for Drinking Water

Copper is the most widely used hard pipe for residential water supply and the safest choice for drinking water because it won't leach chemicals. It offers superior corrosion resistance and handles both hot and cold water effectively. Copper costs $0.50–$2.00 per linear foot depending on wall thickness (M, L, or K grades), with installation requiring soldering. Copper pipes typically last 50–70 years, making them a long-term investment despite higher upfront costs.

soldering ironfluxsoldertubing cutterpipe wrench

Pro tip: If your water has a pH below 7 (acidic), install a water purifier to prevent corrosion that could leach copper into your drinking water—test your water's pH before choosing copper for primary supply lines.

2. PEX Pipes: The Flexible Choice for New Construction

PEX (cross-linked polyethylene) pipes are the rising stars in plumbing, used in approximately 60% of new home construction. They're flexible, resistant to freezing temperatures, and cost $0.40–$1.50 per linear foot—30% cheaper than copper. PEX comes in three types: A (most flexible), B (moderately flexible), and C (rigid for repairs). Color-coded red for hot and blue for cold water lines, PEX requires either expansion tools (PEX-a) or crimp rings (PEX-b) for connections.

15–20 minutes per connection expansion tool or crimp tooltubing cutterdeburring tool

Pro tip: PEX-a (cold expansion) creates the strongest connections and handles freezing better than PEX-b, making it ideal for outdoor sprinkler systems and radiant floor heating where temperature fluctuations are extreme.

3. PVC Pipes: The Budget Option for Cold Water and Drainage

PVC (polyvinyl chloride) pipes are lightweight, affordable at $0.25–$0.80 per linear foot, and perfect for cold water applications and drainage systems. They've been used since the 1950s and are available in most hardware stores. However, PVC cannot handle water temperatures above 140°F and will warp or leach chemicals in hot water applications. PVC is ideal for irrigation, outdoor faucets, drain-waste-vent (DWV) systems, and sewage applications.

PVC cuttersolvent cementprimersandpaper

Pro tip: Always use primer before solvent cement on PVC joints—skipping this step reduces joint strength by 20–30% and increases failure risk within 5 years.

4. CPVC Pipes: The Hot Water Upgrade to PVC

CPVC (chlorinated polyvinyl chloride) is PVC's heat-tolerant cousin, handling water up to 200°F safely. At $0.35–$1.00 per linear foot, it costs only slightly more than PVC while offering versatility for both hot and cold water lines. CPVC is commonly used in domestic hot water supply lines and commercial plumbing where temperature tolerance matters. Installation is similar to PVC, using solvent cement and primer.

CPVC cuttersolvent cementprimersandpaper

Pro tip: CPVC and PVC cannot be directly connected—if you need to transition between them, use a brass or metal adapter fitting to avoid chemical incompatibility that causes joint failure.

5. ABS Pipes: The Strong Lightweight Option for Drainage

ABS (acrylonitrile butadiene styrene) pipes are strong, lightweight, and affordable at $0.30–$0.75 per linear foot. They're primarily used for drain, waste, and vent (DWV) systems and are less common than PVC for these applications. ABS offers excellent impact resistance and chemical resistance, making it ideal for areas prone to temperature swings or mechanical stress. Some municipalities restrict ABS, so verify local codes before installation.

ABS cutterABS cementsandpaper

Pro tip: ABS cement has a shorter working time (30–60 seconds) compared to PVC cement—practice dry-fitting your joints first to ensure smooth, confident assembly during actual installation.

6. Brass Pipes: The Premium Choice for Visible Plumbing

Brass pipes are a premium option costing $1.50–$4.00+ per linear foot, reserved for decorative or exposed plumbing in bathrooms, kitchens, and outdoor water features. They're corrosion-resistant, heat-resistant, and allow tight seals due to brass's soft metal properties. Modern, lead-free brass is safe for water supply lines, water removal lines, and gas lines (where code permits). For residential projects, 20- or 22-gauge brass products are typically sufficient.

pipe wrenchthread sealant tapehacksaw or pipe cutter

Pro tip: Brass requires thread-seal tape and proper torque when connecting—over-tightening brass fittings can crack them, while under-tightening causes leaks; apply moderate pressure until snug, then add one-half turn.

7. Galvanized Steel and Cast Iron: The Legacy Options for Main Lines

Galvanized steel and cast iron pipes are rarely used in modern homes but still appear in older properties and main sewer lines. Galvanized steel costs $1.00–$2.50 per linear foot and was common for water supply before copper became standard; it's prone to rust after 40–50 years. Cast iron is heavier and more expensive ($2.00–$4.00 per linear foot) but remains the standard for main sewer lines due to durability and sound dampening. Both require professional installation and specialized threading equipment.

pipe wrenchthreading machinethread sealant tapehacksaw

Pro tip: If replacing galvanized steel supply lines, transition to copper or PEX rather than re-galvanizing—the cost difference is minimal, but modern materials last 50+ years versus galvanized's 40-year lifespan.

Bonus Tip

Match Pipe Material to Your Water Chemistry

Your water's pH level and mineral content determine which pipe material performs best. Acidic water (pH below 7) can corrode copper and galvanized steel, requiring treatment before installation. Hard water with high mineral content can cause scale buildup in PEX and copper, reducing flow by 10–15% annually. Request a free water quality test from your municipal water department before selecting materials for main supply lines.

What to Avoid

  • Using PVC for hot water applications—temperatures above 140°F cause PVC to warp and leach chemicals like BPA into drinking water; use CPVC or copper instead.
  • Mixing incompatible pipe materials without proper adapters—PVC and CPVC cannot be directly solvent-welded together, and galvanized steel connected directly to copper causes galvanic corrosion that fails within 5–10 years.
  • Skipping local code verification—some municipalities restrict ABS pipes, require lead-free solder on copper, or mandate specific materials for main water lines; installing non-compliant pipes can result in failed inspections and costly rework.
  • Installing copper pipes in acidic water without treatment—pH below 7 causes pinhole leaks within 10–15 years; always test water chemistry before committing to copper for primary supply lines.