6 Questions to Ask Before Hiring a Radon Mitigation Contractor (2026)

1. Are you certified by NRPP or NRSB?

Radon mitigation requires specific technical knowledge — where to place suction points, how to seal entry routes, and how to design the ventilation system for your specific foundation type. The National Radon Proficiency Program (NRPP) and National Radon Safety Board (NRSB) certify contractors who have passed competency exams and maintain continuing education. Many states require this certification by law. An uncertified installer may reduce radon levels initially but miss secondary entry points that cause the system to underperform within months.

5 minutes to verify online

Pro tip: Verify the certification at nrpp.info or nrsb.org. Ask for the certification number and check it yourself — fraudulent claims are not uncommon.

2. What type of system are you recommending and why?

The most common residential system is sub-slab depressurization — a pipe through the slab connected to a fan that creates negative pressure under the foundation, pulling radon out before it enters the house. But the system design depends on your foundation: slab-on-grade, full basement, crawl space, or combination. The number of suction points, fan size, and pipe routing all vary. A contractor should explain why their proposed design fits your specific foundation, not offer a one-size-fits-all solution.

N/A — consultation question

Pro tip: Ask how many suction points are included. Homes with complex foundations or large footprints often need 2-3 suction points. A single-point system in a large home may underperform.

3. What radon level do you guarantee after installation?

The EPA action level is 4.0 pCi/L, but many mitigation systems reduce levels to below 2.0 pCi/L. A reputable contractor should guarantee reducing your radon level to below 4.0 pCi/L and should specify what happens if that guarantee is not met — additional work at no charge, system modification, or refund. A contractor who will not provide a post-mitigation guarantee has no confidence in their system design.

N/A — contract term

Pro tip: The guarantee should be based on a post-mitigation test conducted at least 24 hours after installation with the system running. Insist on a third-party test, not one conducted by the installer.

4. Does the price include post-mitigation testing?

A radon mitigation system is only verified effective by a post-installation test. Some contractors include this in their price; others treat it as an add-on. The test should be conducted 24-48 hours after installation and should ideally be performed by a different company than the one that installed the system to avoid conflict of interest. If the installer does the post-test, at minimum they should use a continuous radon monitor with tamper-evident data logging.

N/A — cost clarification

Pro tip: If the installation is for a real estate transaction, the buyer's agent may require an independent post-test regardless. Budget $150-$200 for an independent test.

5. Where will the vent pipe be routed and how will it look?

The radon vent pipe must extend above the roofline to discharge safely. Interior routing through a closet or utility chase is least visible but requires roof penetration. Exterior routing along the outside wall is easier to install but visually prominent. The pipe location affects your home's appearance and can impact future resale. Discuss the routing before installation — relocating a pipe after installation is expensive.

N/A — design discussion

Pro tip: If the vent pipe runs on the exterior, it should be on a side or rear elevation, not the front of the house. Exterior pipe on the front facade is a visible indicator of radon problems that concerns future buyers.

6. What is the ongoing maintenance and electricity cost?

Active radon mitigation systems use a fan that runs 24/7. The fan consumes $50-$150 in electricity per year depending on size. Fans have a 5-10 year lifespan and cost $150-$300 to replace. The system should include a manometer (U-tube gauge) on the pipe that lets you verify the fan is creating suction — a quick visual check. Ask the contractor to explain what the manometer reading should be and what to do if it drops to zero.

N/A — ownership question

Pro tip: Check the manometer monthly — it takes 5 seconds. If the fluid level is equal on both sides, the fan has failed and radon levels will return to pre-mitigation levels within days.

Bonus Tip

Retest your radon levels every 2 years, even with a system installed

Foundation conditions change, new cracks develop, and fans wear out gradually. A system that worked perfectly 3 years ago may be underperforming now. The EPA recommends retesting every 2 years. A short-term test kit costs $15-$30 and takes 2-7 days. It is the cheapest way to verify your family is still protected.

What to Avoid

  • Hiring an uncertified contractor to save money — radon mitigation is not general contracting; improper installation creates a false sense of security.
  • Accepting a verbal guarantee instead of a written post-mitigation performance guarantee.
  • Choosing a system based solely on lowest price — fan size, suction point count, and sealing quality vary significantly between quotes.
  • Skipping the post-installation test because 'the system is running' — a running fan does not guarantee effective radon reduction.