10 Questions to Ask Before Emergency Generator Hookup (2026)

1. Transfer switch or interlock kit — which is right for my situation?

A transfer switch ($500–$2,000 installed) is a separate panel that lets you switch specific circuits from utility to generator. An interlock kit ($200–$500 installed) is a mechanical bracket on your existing panel that prevents the main and generator breakers from being on simultaneously. Both are code-legal. Ask which your electrician recommends based on how many circuits you need to back up and your budget.

Discussion

Pro tip: If you only need to back up 4–6 circuits (refrigerator, furnace, well pump, a few lights), an interlock kit is usually the better value. If you want whole-home backup or automation, invest in a full transfer switch.

2. What size generator do I need to run my essential circuits?

Undersizing the generator is the most common mistake. A 3,500-watt generator runs lights and a refrigerator. A 7,500-watt generator adds a well pump and furnace blower. A sump pump, window AC, or electric range requires 10,000+ watts. Ask the electrician to calculate the total starting watts (not just running watts) for the circuits you want to power — motor loads like pumps and compressors draw 2–3x their running wattage on startup.

10 minutes

Pro tip: Ask about load management: staggering when appliances start so they don't all surge the generator simultaneously. A smaller generator with load management can handle the same appliances as a larger one without it.

3. Can you install the hookup today, or what's your emergency availability?

During storm season, every electrician in the area gets swamped with generator hookup requests. If you're calling during or after a storm, ask about emergency availability and be ready to pay a premium. A standard hookup takes 2–4 hours. Same-day emergency service typically costs 1.5x to 2x the standard rate but gets you powered while your neighbors are still in the dark.

2 minutes on phone

Pro tip: If a major storm is forecast, call your electrician before it hits. Scheduling a hookup 2 days before the storm is cheaper and more available than calling during the outage.

4. Where should I place the generator for safe operation?

Carbon monoxide from a running generator kills over 70 people annually in the U.S. The generator must be at least 20 feet from any window, door, or vent, and the exhaust must point away from the house. Ask the electrician where to position the generator relative to your inlet box, fuel storage, and prevailing wind direction. They see dozens of setups and know what works.

Discussion during install

Pro tip: Install a battery-operated carbon monoxide detector on every level of your home, especially near bedrooms. A $25 detector is the last line of defense against an improperly positioned generator.

5. Do I need a permit for the generator hookup?

Most jurisdictions require an electrical permit for transfer switch or interlock kit installation because it involves modifying the main panel. The electrician should pull the permit and schedule the inspection. Unpermitted generator hookups can void your homeowner's insurance and create problems when selling the home.

2 minutes

Pro tip: Ask the electrician whether the permit fee is included in their quote. Permit costs range from $50 to $200 depending on jurisdiction and are sometimes listed as an extra.

6. What type of inlet box do you install, and where will it go?

The inlet box is the exterior receptacle where you plug the generator cord into your home. It should be a weatherproof NEMA 3R box mounted on the exterior wall near where you'll position the generator. The inlet's amperage rating must match or exceed the generator's maximum output. Common sizes are 30-amp (for portable generators up to 7,500 watts) and 50-amp (for larger units).

Discussion

Pro tip: Ask the electrician to mount the inlet on the same side of the house where you'll store the generator, with a short cord run. Every extra foot of cord adds voltage drop and reduces the power reaching your panel.

7. What wire gauge and cord type do I need from the generator to the inlet?

The cord between your generator and the inlet box must be properly sized for the amperage. A 30-amp hookup requires 10-gauge wire. A 50-amp hookup requires 6-gauge wire. Using an undersized cord creates a fire hazard — the cord overheats before the breaker trips. Ask the electrician to recommend the specific cord and whether they supply it.

Discussion

Pro tip: Buy a generator cord with twist-lock connectors on both ends. Standard plugs can vibrate loose from generator vibration, cutting power when you need it most.

8. Which circuits should I prioritize on the transfer switch?

You can't run your entire house on a portable generator. Prioritize: refrigerator, furnace blower, well pump (if applicable), sump pump (if flood risk), a bathroom circuit, and a few lighting circuits. Air conditioning, electric stoves, electric water heaters, and electric dryers typically draw too much power for portable generator backup.

10 minutes

Pro tip: Ask the electrician to put your internet modem/router on a backed-up circuit. Staying connected during an outage lets you monitor weather, communicate, and work from home if needed.

9. How do I safely start up and shut down the generator during a transfer?

The startup and shutdown sequence matters. For manual transfer: start the generator and let it warm up for 2–3 minutes, flip the interlock or transfer switch to generator, then energize circuits one at a time. For shutdown: turn off all backed-up circuits, transfer back to utility position, then shut down the generator. Skipping the warm-up or load-shedding steps can damage the generator and your appliances.

5-minute walkthrough

Pro tip: Ask the electrician to write down the startup/shutdown procedure and tape it inside your panel door. During a 2 AM outage in a storm, you won't remember the verbal walkthrough from the install day.

10. What ongoing maintenance does the hookup need?

The electrical hookup itself — transfer switch, inlet box, and wiring — needs minimal maintenance. But the inlet box seal should be checked annually for water tightness, the transfer switch contactor should be exercised monthly, and the cord should be inspected for damage before each use. Ask the electrician about a maintenance schedule and whether they offer annual check-ups.

Discussion

Pro tip: Run your generator under load for 30 minutes every month. Generators that sit unused for months develop carburetor and fuel system issues. The monthly run also exercises the transfer switch.

Bonus Tip

Consider a generator-ready panel for your next upgrade

If you're already planning a panel upgrade, ask about generator-ready panels (like Generac's PWRview or Eaton's CH panels with integrated interlocks). These panels have the interlock mechanism built in, eliminating the separate transfer switch and saving $300–$500 on the generator hookup installation.

What to Avoid

  • Backfeeding through a dryer or range outlet — this sends power back onto utility lines and can electrocute a lineworker repairing the outage.
  • Running the generator in a garage, basement, or enclosed porch — carbon monoxide accumulates in enclosed spaces and kills within minutes.
  • Using a generator cord that's undersized for your hookup amperage — undersized cords overheat and are a fire hazard.
  • Storing fuel for the generator inside your home or attached garage — gasoline vapors are heavier than air and can reach ignition sources like water heaters or furnace pilots.