9 Questions to Ask Before Hiring an Electrician to Replace Knob-and-Tube Wiring (2026)

1. How will you access the wiring without destroying my walls and ceilings?

Knob-and-tube wiring runs through wall cavities, floor joists, and ceiling bays. Accessing it for replacement requires either opening walls (costly plaster repair afterward) or fishing new wires through existing cavities from strategic access points. The best electricians minimize wall openings by using existing paths — pulling new Romex through the same joist bays by drilling from attics and basements. The worst electricians open entire wall sections and leave you with a $5,000-$10,000 drywall and plaster bill.

5 minutes to ask

Pro tip: Ask to see photos of previous K&T replacement projects showing the wall damage (or lack thereof). An electrician skilled at wire fishing in old homes will proudly show minimal-access results.

2. Does your quote include full patching and painting, or is that separate?

Any access holes cut into walls or ceilings during wiring work need patching, taping, mudding, texturing, and painting to restore the surface. Some electricians include this in their quote (using their own drywall sub). Others quote only the electrical work, leaving you to hire a separate drywall and painting contractor. The repair cost can add $3,000-$8,000 to the project if not included — always clarify before signing.

2 minutes to ask

Pro tip: If patching is not included, get a drywall estimate before committing. The total project cost is electrical + structural restoration — judging only the electrical quote is misleading.

3. Will you replace all circuits or only active knob-and-tube?

Some homes have knob-and-tube that has been partially replaced over decades — some circuits are old, some are modern. Ask whether the electrician will replace ALL wiring (full rewire) or only the remaining K&T circuits. A full rewire costs more but eliminates all legacy wiring issues. A partial approach leaves you with a mix of wire ages and may require future work when the remaining old circuits fail.

5 minutes to discuss

Pro tip: Ask: 'After this project, will any knob-and-tube remain energized in the house?' The answer should be no if you want insurance acceptance and a complete solution.

4. How do you handle insulation that is touching knob-and-tube wiring?

Knob-and-tube wiring was designed to dissipate heat in open air. Insulation touching K&T traps heat and creates fire risk — this is the primary reason insurers reject K&T homes. If insulation has been blown over K&T in your attic or walls, the electrician must either remove the insulation from active K&T areas (reducing energy efficiency) or prioritize replacing those circuits first. Ask their sequencing plan for insulation-contact areas.

5 minutes

Pro tip: After K&T is fully replaced, you can insulate all cavities freely. Budget for insulation work after the rewire — it is often the best time to add attic and wall insulation since cavities are already accessible.

5. What is the panel upgrade plan, and is it included?

Homes with K&T typically have old fuse boxes or undersized panels (60-100 amp). A full rewire almost always requires a new panel (200 amp is current standard) to accommodate the additional circuits, AFCI breakers (now required by code), and future capacity. If the panel upgrade is not included in the K&T replacement quote, you will discover a $2,000-$4,000 surprise when the electrician determines the existing panel cannot handle the new circuit load.

5 minutes to confirm scope

Pro tip: Ask specifically: 'Does your quote include a new 200-amp panel, meter base, and AFCI breakers for bedroom circuits?' These three items are almost always required for a complete K&T replacement.

6. Will the completed work pass insurance inspection for coverage?

Many homeowners replace K&T specifically because their insurance carrier requires it for coverage (or charges a surcharge). Ask the electrician whether their completed work will satisfy your insurer's requirements — some carriers require not just removal of K&T but also AFCI protection, grounding upgrades, or specific panel configurations. Get your insurer's exact requirements in writing and share them with the electrician before work begins.

1-2 hours to gather requirements from insurer

Pro tip: Call your insurance company and ask: 'What specific electrical work is required for you to provide standard coverage without K&T surcharges?' Get this in writing and include it in the electrician's scope of work.

7. What is the realistic timeline, and will my home be without power?

A full K&T replacement in a typical 1,500-2,000 sqft home takes 5-10 working days depending on accessibility and home complexity. During this time, portions of the home will be without power as circuits are replaced sequentially. Ask the electrician for their circuit-by-circuit schedule so you can plan accordingly. Some electricians maintain temporary power to critical circuits (refrigerator, HVAC) throughout the project.

5 minutes to discuss

Pro tip: Ask: 'Will my refrigerator and HVAC have power throughout the project?' If yes, ask how — they should be running temporary feeds from circuits being done last.

8. Do you have experience specifically with homes of my era and construction type?

K&T exists primarily in homes built before 1950 — balloon-frame, plaster-and-lath, with construction details that modern electricians may not understand. An electrician experienced with 1920s balloon-frame homes knows how to fish wires through plaster walls without crumbling them, where to access stacked wall cavities, and how to work around legacy gas lines and lead pipes. An electrician experienced only with new construction will cause more damage and take longer.

5 minutes to verify

Pro tip: Ask how many K&T replacement projects they have completed in the past 2 years, and in what construction types. Three or more in similar homes to yours is a strong indicator of relevant experience.

9. What permits are required, and who pulls them?

K&T replacement requires electrical permits in every jurisdiction — there are no exceptions. The electrician should pull the permit (not you), schedule inspections, and ensure the work passes before final payment. Ask who is responsible for addressing any failed inspection items. Unpermitted K&T replacement creates legal and insurance liability, and cannot be verified as safe by any third party.

2 minutes to confirm

Pro tip: Ask for the permit number after it is pulled and verify it is active with your local building department. Some contractors claim they will pull permits but never do — verification protects you.

Bonus Tip

Get a written confirmation that all K&T has been de-energized upon completion

After the project, request a signed letter from the electrician stating that all knob-and-tube wiring in the home has been de-energized or removed. This letter is what your insurance company needs to remove the K&T surcharge or reinstate coverage. Without it, you have no proof for your insurer even if the work was done correctly.

What to Avoid

  • Hiring the cheapest bidder without verifying their old-home experience — inexperienced electricians cause $5,000-$10,000 in wall/ceiling damage that their quote did not include repairing.
  • Attempting partial K&T replacement to save money when insurance requires full removal — partial work that leaves any energized K&T does not satisfy insurer requirements.
  • Allowing the electrician to simply abandon K&T in place without verifying it is de-energized — dead K&T is harmless, but 'abandoned' wiring that is still connected at one end is a hidden hazard.
  • Signing a contract without a fixed total price — K&T replacement scope is knowable and should be firm-quoted after inspection, not open-ended time-and-materials.