1. Using indoor-rated wire and connectors outdoors
Standard NM (Romex) cable and twist-on wire nuts are not rated for moisture, UV exposure, or direct burial. Within one season, the jacket degrades, connections corrode, and you get intermittent failures or ground faults. Outdoor wiring requires UF-B cable for direct burial, weatherproof boxes rated NEMA 3R or higher, and silicone-filled or gel-filled connectors. The material cost difference is $50–$100 per run. The replacement cost after failure is $500–$1,000.
Pro tip: If your low-voltage landscape lighting uses twist-on wire nuts underground, replace them with waterproof crimp connectors filled with dielectric grease. This single change eliminates most landscape lighting failures.
2. Burying cables too shallow without conduit
UF-B cable must be buried at least 24 inches deep without conduit, or 18 inches in conduit, per NEC. Low-voltage landscape lighting cable should be at least 6 inches deep. Cables buried 2–3 inches under mulch get hit by edgers, shovels, and aeration machines. Every cut cable is a service call, and every splice underground is a future failure point. Bury it right the first time.
Pro tip: Run a continuous piece of cable from the transformer to the last fixture — no underground splices. Every underground connection is a potential failure in 3–5 years.
3. Oversizing or undersizing the transformer for low-voltage systems
An undersized transformer drops voltage to far fixtures, making them dim and yellow. An oversized transformer wastes energy and can over-drive bulbs, shortening their life. Calculate total wattage of all connected fixtures, add 20% for future expansion, and size the transformer accordingly. For runs over 50 feet, use heavier gauge wire (10 AWG instead of 12 AWG) to compensate for voltage drop.
Pro tip: Measure voltage at the last fixture in the run with a multimeter. Low-voltage LED fixtures should receive 10.8–12.0 volts. Below 10.5V, increase wire gauge or shorten the run.
4. Pointing fixtures directly at windows and neighbors
Outdoor lighting should illuminate the ground, architectural features, and pathways — not blast light horizontally into bedroom windows (yours or your neighbor's). Glare from poorly aimed fixtures creates light trespass, which is a code violation in many municipalities and a guaranteed neighbor dispute. Every fixture should be aimed downward or at a surface, never directly outward at eye level.
Pro tip: Walk your property at night after installation and check every fixture from your neighbor's perspective. Adjust any fixture that produces visible glare from their yard or windows.
5. Neglecting to install a weatherproof GFCI at the feed point
Every outdoor circuit must be GFCI-protected, and the GFCI device must be accessible — not buried in a junction box behind bushes. Missing GFCI protection on outdoor circuits is a code violation and an electrocution risk, especially when wet ground provides a path to earth. Install a weatherproof GFCI outlet or a GFCI breaker in the panel for every outdoor lighting circuit.
Pro tip: GFCI breakers in the panel are more reliable for outdoor circuits than GFCI outlets exposed to weather. The breaker stays dry, the outdoor connection stays simple.
6. Installing fixtures without a plan — then rearranging later
Placing fixtures by intuition rather than a lighting plan results in hot spots, dark zones, and a layout that looks random from the street. Moving fixtures after installation means re-trenching, new cable runs, and patching disturbed landscaping. Spend an hour at night with a flashlight mocking up positions before committing to any wiring. Mark each fixture location with a stake and live with it for a few nights before trenching.
Pro tip: Use the three-layer approach: ambient (path lights), accent (uplights on trees and architecture), and task (door and step lights). Each layer serves a different purpose and prevents the all-or-nothing look.
7. Forgetting about maintenance access when placing transformers and junction boxes
A transformer mounted behind a mature shrub or a junction box buried under a deck becomes invisible — until it fails and you can't reach it without removing landscaping or demolition. Mount transformers at least 12 inches off the ground in accessible locations. Place junction boxes where you can open them without digging or dismantling structures. You will need to access these components for maintenance, troubleshooting, and lamp replacement.
Pro tip: Take a photo of each junction box location and save it with your home files. In 5 years, you will not remember where they are buried.
Bonus Tip
Install a photocell or astronomical timer instead of a manual switch
Manual switches get left on during daylight and forgotten at night. A photocell turns lights on at dusk and off at dawn automatically. An astronomical timer adjusts for seasonal changes in daylight length without manual reprogramming. Either option costs $20–$60 and saves you from the ongoing annoyance of managing outdoor lights manually.
What to Avoid
- Using standard electrical tape on underground splices — it unravels in soil within months and exposes bare connections.
- Running landscape lighting cable through PVC conduit without pull points — when a section fails, you can't replace it without digging up the entire run.
- Mixing LED and halogen fixtures on the same transformer — they have different voltage requirements and the LEDs will flicker or burn out.
- Mounting fixtures directly against wood siding or deck boards without standoffs — trapped moisture rots the wood behind the fixture.