1. Most insurance carriers will not write a policy on a home with active knob-and-tube
Knob-and-tube (K&T) wiring, installed primarily from 1880 to 1940, is not inherently illegal or code-violating in existing installations. But insurance companies view it as an unacceptable fire risk, and many — including most major carriers — refuse to issue homeowner's insurance on homes with active K&T circuits. Without insurance, your mortgage lender will not close the loan. Before making an offer, confirm with your insurance agent that they will write a policy. If they won't, the home requires rewiring before closing.
Pro tip: Some specialty insurers will cover K&T homes at a premium of 20–40% above standard rates. Ask your agent about surplus lines carriers if standard carriers decline.
2. K&T wiring has no ground wire — every outlet is ungrounded
Knob-and-tube wiring carries only two conductors: hot and neutral. There is no equipment grounding conductor. This means every outlet on a K&T circuit is a two-prong, ungrounded outlet. Grounding provides a safe path for fault current — without it, a short circuit in an appliance can energize the metal chassis and electrocute anyone touching it. Adding three-prong outlets to K&T circuits without adding a ground wire is a code violation and a dangerous false sense of security.
Pro tip: If you see three-prong outlets in a home with K&T wiring, they were either incorrectly installed on K&T circuits or the home has a mix of old and new wiring. An electrician can determine which circuits are K&T with a simple test.
3. Insulation covering K&T wiring is a fire hazard
K&T wiring was designed to dissipate heat into open air — the ceramic knobs and tubes hold the wire away from framing with an air gap. When blown-in insulation covers K&T wiring, the wire cannot shed heat, and the temperature rises. Add a high-draw appliance on an already-warm circuit and the wire can reach temperatures that ignite the surrounding insulation. Any attic or wall insulation retrofit in a K&T home must either avoid covering the wiring or require the wiring to be replaced first.
Pro tip: If the home had insulation blown into attic or wall cavities and K&T is still active, the insulation is likely covering wires. This combination is the highest-risk scenario and requires immediate professional evaluation.
4. Partial rewires are common — and create their own problems
Many K&T homes have been partially rewired over the decades: the kitchen and bathrooms were updated, but bedrooms, attics, and basements still run on original wiring. Partial rewires create a patchwork system where old and new wiring coexist, often with questionable connections between them. Copper-to-K&T splices require specific techniques and materials. If the partial rewire was done without permits, you have no assurance the connections are safe.
Pro tip: Ask the seller for the permit history of any electrical work. If they can't produce it, assume the partial rewire was unpermitted and budget for a full rewire.
5. A full rewire costs $10,000–$25,000 — negotiate accordingly
A whole-house rewire in a K&T home is not a minor repair — it is a major project that involves opening walls, running new cable, installing a modern panel, and patching drywall. The cost depends on the size of the home, the number of floors, and the access available through attics and basements. This cost should be factored into your offer price as a direct deduction, not a vague 'we'll figure it out later.' Get a rewire estimate from a licensed electrician before making your offer.
Pro tip: Frame the negotiation as a safety requirement, not a preference. 'The home requires a $15,000 rewire to obtain insurance and meet safety standards' is harder for a seller to argue against than 'I'd like updated wiring.'
6. The wiring itself may be in good condition — the connections are the problem
Ironically, K&T wire insulation — typically rubberized cloth over solid copper — can last 80+ years if undisturbed in dry conditions. The failure points are the connections: where K&T meets modern wiring, where splices were made with electrical tape instead of proper methods, and where the rubber insulation has dried, cracked, and fallen away from decades of heat. An experienced electrician can assess whether the wire itself is intact or whether the insulation has deteriorated beyond safe use.
Pro tip: Ask the electrician to check K&T insulation condition in accessible areas — attic and basement. If the insulation crumbles when touched, the wire is beyond its useful life regardless of the copper's condition.
Bonus Tip
Get the electrician's assessment in writing before your inspection contingency expires
Your inspection contingency gives you a window — usually 7–10 days — to investigate and negotiate or walk away. A general home inspector identifies K&T but cannot assess its full scope or cost to remediate. Hire a licensed electrician within days of the home inspection to evaluate the extent of K&T, the condition of the wiring, and provide a written estimate for full remediation. This estimate becomes your negotiation tool.
What to Avoid
- Accepting seller assurances that 'the K&T is inactive' without verification — deactivating K&T requires physically disconnecting it at the panel, not just turning off breakers.
- Adding three-prong outlets to K&T circuits as a 'fix' — this is a code violation that creates a false sense of grounding protection.
- Blowing insulation over active K&T wiring to improve energy efficiency — this creates a fire hazard by trapping heat around conductors designed for open-air cooling.
- Assuming a partial rewire means the house is safe — mixed K&T and modern wiring with improper connections can be more dangerous than all-K&T.