6 Irrigation System Winterization Steps (2026 Guide)

1. Shut Off the Main Water Supply Valve

Locate the irrigation shut-off valve near your water meter, in the basement, crawlspace, or a yard box, and turn it fully clockwise to stop flow. This prevents new water entry, reducing freeze risk by 80% in un-drained lines. Outdoor valves fail 15% more often without insulation, costing $200 average replacement.

10 minutes ScrewdriverInsulation foam

Pro tip: Wrap the valve with $5 foam pipe insulation rated to -20°F for extra protection in northern climates where mid-fall freezes hit early.

2. Turn Off and Store the Irrigation Controller

Switch the controller to 'off' or 'rain mode' to halt all scheduling, then unplug it or remove the battery to avoid electrical shorts from 20% winter humidity spikes. Controllers cost $100-$300 to replace if moisture damages internals. In milder climates, this step alone cuts unnecessary activations by 100%.

5 minutes None

Pro tip: Store the controller indoors at 60-70°F to extend its 5-7 year lifespan by preventing circuit corrosion from cold exposure.

3. Drain the Backflow Preventer Completely

Open all test cocks and drain valves on the backflow device, tilting it if needed to empty residual water that expands 9% when frozen. Backflow failures account for 40% of winter claims, with repairs at $250-$600. In Texas mild freezes, this step suffices without blowout for 90% systems.

15 minutes WrenchBucket

Pro tip: Detach and store the preventer indoors if possible—units under 50 lbs reduce field failure by 70% versus leaving them exposed.

4. Blow Out the Lines with an Air Compressor

Connect a compressor to the backflow port, limit to 80 PSI max, and blow each zone for 1-2 minutes starting from the farthest head. This removes 99% of water versus manual draining's 70%, preventing $1,000+ pipe bursts. Rentals cost $40-$60/day for 10+ gallon units.

45 minutes Air compressor (10+ CFM)Compressor adapter

Pro tip: Blow in short 30-second bursts per zone to avoid 25% higher damage risk from sustained pressure over 50 PSI.

5. Insulate All Exposed Above-Ground Components

Wrap pipes, valves, and risers with $10-$20 foam sleeves or heat tape rated to -40°F, securing with tape to block 95% of frost penetration. Uninsulated parts crack in 60% of mild freezes under 28°F. This adds 2-3 years to component life, saving $150/year on replacements.

30 minutes Foam insulationDuct tape

Pro tip: Layer insulation 1.5 inches thick on PVC pipes in mountain regions like Asheville, where November freezes strike 20% earlier than coasts.

6. Inspect and Mark the System for Spring

Walk zones to flag damaged heads (5-10% annual wear) or leaks, costing $15-$50 per head to fix pre-spring. Mark shut-off locations with glow stakes for 50% faster reactivation. Skipping raises spring startup delays by 2 weeks, per 70% of homeowner reports.

20 minutes Garden flagsFlashlight

Pro tip: Photograph zones before covering for insurance claims—processed claims recover 85% of $800 average damages.

Bonus Tip

Schedule a Professional Inspection if Unsure

Hire certified techs for $100-$250 to verify blowout PSI and backflow drain, catching 30% more issues than DIY. Pros use shop compressors at 40-50 CFM, reducing re-freeze risk to under 2%. Book in early fall to beat 50% post-frost rush.

What to Avoid

  • Skipping blowout: Leaves 20-30% residual water, causing 60% of $1,200 pipe bursts in first freeze.
  • Exceeding 80 PSI air pressure: Damages 25% of sprinkler heads, with repairs at $200+ per zone.
  • Ignoring backflow drainage: Accounts for 40% of failures, $400 average fix plus permit fees.
  • Delaying past mid-30s nights: Hard freezes below 32°F for 4+ hours burst un-prepped lines in 80% cases.