1. Check whether the estimate uses Xactimate pricing
Xactimate is the software that 90%+ of insurance carriers use to generate damage repair estimates. It calculates costs using standardized regional labor and material rates updated monthly. When a restoration company provides an estimate that doesn't match Xactimate line items, the adjuster will rewrite it in Xactimate anyway — and the discrepancy creates delays and disputes. Ask each company whether their estimate is Xactimate-based. If it is, the adjuster can compare line by line in minutes. If it isn't, you'll spend weeks going back and forth.
Pro tip: If you have access to your adjuster's Xactimate estimate, share it with contractors and ask them to match the line-item format. This makes comparison straightforward and speeds up approval.
2. Compare the water damage category and class ratings across estimates
Water damage is classified by contamination (Category 1–3) and severity (Class 1–4). Category 1 is clean water from a supply line; Category 3 is sewage or floodwater. Class 1 affects a small area with minimal absorption; Class 4 involves deep saturation into hardwood, plaster, or concrete. Each step up in category and class costs significantly more because it requires more aggressive remediation. If one estimate says Category 2/Class 2 and another says Category 3/Class 4 for the same event, someone is wrong — and the difference could be $5,000+.
Pro tip: Category can escalate over time. Clean water (Cat 1) that sits for 48+ hours becomes grey water (Cat 2) due to bacterial growth. If there's a dispute about category, the timestamp of when the water loss started vs. when remediation began determines who's right.
3. Look for line-item scope differences, not just total price
Two estimates can show the same total — $8,000 — but include completely different scope. One might include full drywall replacement with texture matching, while the other patches drywall but charges for unnecessary carpet replacement. Compare estimates line by line: demolition scope, drying equipment quantity and duration, material replacement specifications, and what's included vs. excluded. The cheapest estimate isn't always the best value if it skips critical steps like antimicrobial treatment or moisture verification.
Pro tip: Create a simple spreadsheet with each major task as a row and each contractor as a column. This makes scope gaps immediately visible — you'll see who includes content manipulation (moving furniture) and who charges it as an add-on.
How to do it:
- List every major task from all estimates in a single column: demo, drying, antimicrobial, drywall, paint, flooring, etc.
- For each contractor, fill in their price for that task. Use $0 if they don't include it.
- Highlight any task where one contractor's price is 2x+ another's.
- Highlight any task that appears in only one estimate — it's either necessary and others missed it, or unnecessary and inflated.
- Ask each contractor to explain their scope for any highlighted discrepancies.
4. Verify the drying equipment count and rental duration
Drying equipment (dehumidifiers and air movers) is one of the biggest cost drivers in water damage restoration — and the most commonly inflated. The IICRC S500 standard specifies one air mover per 10–16 linear feet of affected wall and one dehumidifier per 1,000–1,500 sq ft. If an estimate shows 12 air movers for a 200 sq ft bathroom, that's overkill. Equipment rental runs $25–$75 per day per unit. A company that places excess equipment and runs it for 5 days instead of 3 can add $1,000–$3,000 to the bill.
Pro tip: Ask each company how many drying days they estimate and what moisture readings they'll use to determine when drying is complete. The answer should reference specific moisture content targets (typically below 15% for wood), not just a number of days.
5. Ask whether moisture verification is included or billed separately
Professional water damage restoration should include daily moisture readings to monitor drying progress and a final verification reading confirming materials have reached target moisture content before rebuild begins. Some companies include this in their drying fee; others bill $50–$150 per reading session as a separate line item. If a company skips moisture verification entirely, that's a red flag — rebuilding over wet materials leads to mold growth within 2–4 weeks, and the entire job has to be redone.
Pro tip: Request copies of all moisture readings when the job is done. These readings are your documentation that the drying was completed properly — critical if mold develops later and you need to prove the restoration company didn't do their job.
6. Check if demolition scope matches the actual water contact area
The industry standard is to remove drywall 12–24 inches above the visible water line to account for wicking. Some contractors remove drywall floor to ceiling 'to be safe,' but that's often unnecessary and doubles the rebuild cost. Compare the demolition scope in each estimate against the actual flood height. If water reached 18 inches up the wall, removing drywall to 36–42 inches is standard. Removing to ceiling height should only happen if moisture readings show saturation above the 42-inch mark.
Pro tip: Ask each contractor to show you where they'll cut on the actual wall. If they can't point to a specific height and explain why, they're guessing — not measuring.
7. Compare content manipulation and storage charges
Content manipulation means moving your belongings out of the work area so drying equipment can be placed effectively. Pack-out means boxing up contents and storing them off-site during restoration. Manipulation costs $200–$800; full pack-out and storage runs $1,500–$5,000+. Some estimates include manipulation; others include full pack-out for the same job. Unless the entire home is affected, manipulation (moving items to unaffected rooms) is usually sufficient and far cheaper than off-site storage.
Pro tip: If pack-out is recommended, ask specifically which items need off-site storage and why. Electronics and upholstered furniture exposed to Category 2–3 water may genuinely need off-site cleaning. Your winter clothes in an unaffected closet do not.
8. Confirm whether mold testing is included or recommended separately
Water damage and mold go hand in hand — mold begins growing on wet materials within 24–48 hours. Some estimates include post-remediation mold testing; others exclude it, leaving you to discover mold months later. If your water event involved Category 2 or 3 water, or if materials were wet for more than 48 hours, post-remediation mold testing ($200–$500) is a necessary expense, not an optional upsell. Compare how each estimate handles mold prevention and testing.
Pro tip: Hire a third-party mold inspector for post-remediation testing — not the same company doing the restoration. The company doing the work has a financial incentive to pass their own inspection.
9. Ask about warranty and callback policy for the completed work
Water damage restoration failures show up 2–8 weeks after completion: mold growth behind new drywall, buckling in flooring, musty odors that indicate incomplete drying. A reputable company offers a warranty (typically 1–5 years) that covers these callbacks at no additional cost. If a company won't put a warranty in writing, that tells you how confident they are in their own work. Compare warranty terms across estimates — a slightly higher price with a 3-year warranty beats a bargain price with no guarantee.
Pro tip: Get the warranty in writing as part of the contract, not as a verbal promise. Specify that the warranty covers mold remediation if mold develops in treated areas within the warranty period.
Bonus Tip
Get your own independent Xactimate estimate
Public adjusters and independent estimators can create a Xactimate estimate that represents your interests, not the insurance company's or the contractor's. This costs $300–$500 but gives you a benchmark to compare all other estimates against. When your contractor's $12,000 estimate, the adjuster's $7,000 estimate, and your independent $10,000 estimate are all on the table, the negotiation converges on fair pricing much faster.
What to Avoid
- Accepting the insurance company's first estimate without question — the initial adjuster estimate is a starting point for negotiation, not a final offer.
- Choosing the lowest bid without comparing scope — the cheapest contractor often skips antimicrobial treatment, moisture verification, or adequate drying time, leading to mold and re-work.
- Signing a restoration contract before your insurance company has inspected the damage — your insurer may require specific documentation or pre-approval for certain scope items.
- Letting a contractor pressure you into signing immediately after the water event — legitimate restoration companies understand you need time to compare estimates and coordinate with your insurer.