1. Inspect and Assess All Surfaces First
Walk the entire home to note peeling paint, rot, caulk failures, and stains before starting. Skipping inspection causes 60% of paint failures due to hidden damage. This step identifies issues early, preventing $1,000+ in future repairs.
Pro tip: Use a moisture meter on wood; readings over 15% signal rot needing replacement before priming.
2. Pressure Wash at 2000-2500 PSI
Remove dirt, mildew, and loose paint with a pressure washer at 2000-2500 PSI for most siding; mildew solution costs $20-$40 per gallon. This ensures 90% better paint adhesion than washing by hand. Allow 24-48 hours drying to avoid trapped moisture blistering.
Pro tip: Tilt nozzle 45 degrees to avoid damaging wood siding; test on inconspicuous area first.
3. Scrape All Loose and Peeling Paint
Scrape flaking paint to bare wood or solid edges using a carbide scraper; covers 500 sq ft per hour. Painting over loose paint fails in 1 year 75% of the time. Expect 10-20% surface exposure on older homes.
Pro tip: Work top-down to catch debris; wear a dust mask as scraped paint generates 5-10 lbs of waste.
4. Sand Rough Edges with 80-120 Grit
Feather scraped areas smooth with 80-120 grit sandpaper or orbital sander for mechanical paint bond. Sanding boosts adhesion by 50% on glossy surfaces. A quality sander rents for $30/day, saving 4x time over hand sanding.
Pro tip: Use dustless sanding vacuum on pre-1978 homes to contain lead dust, reducing health risks by 95%.
5. Caulk All Gaps and Trim Joints
Seal windows, doors, and trim with paintable exterior caulk using a caulk gun; one 10 oz tube covers 30 linear feet. Caulking prevents 80% of water intrusion failures. Costs $5-$8 per tube, extending paint life by 4 years.
Pro tip: Cut nozzle at 45-degree angle for 1/4-inch bead; tool smooth within 10 minutes for waterproof seal.
6. Repair Damaged Wood and Surfaces
Fill cracks with exterior wood filler ($15/tub, cures in 1 hour) or replace rotted sections with epoxy ($25/kit). Unrepaired damage causes 65% of blistering. Professional repair averages $500-$1,500 for 100 sq ft.
Pro tip: Drill drainage holes in rot pockets before filling; epoxy bonds 3x stronger than filler alone.
7. Prime Bare Wood, Stains, and Repairs
Apply stain-blocking primer to exposed areas with a brush; one gallon ($40-$60) covers 300-400 sq ft. Priming reduces topcoat needs by 1 layer, saving $100-$200 in paint. Essential for color changes over 3 shades.
Pro tip: Prime screws/nails with metal primer to block rust bleed-through, preventing 90% of spot failures.
8. Prime All Six Sides of New Trim
Coat unpainted sides of new siding or trim to prevent moisture absorption and blistering; adds 20-30% prep time but extends life 5+ years. Primer costs $0.15-$0.20/sq ft. Skipping causes 40% of new material failures.
Pro tip: Back-prime before installation; wet primer penetrates 1/16-inch, sealing against vapor drive.
Bonus Tip
Mask and Protect Landscaping Last
Cover plants, lights, and walkways with plastic sheeting and drop cloths before painting; painter's tape ($10/roll) prevents 95% of overspray damage. Work top-to-bottom to avoid drips on protected areas. This final shield saves $200-$500 in cleanup and fixes.
What to Avoid
- Painting over dirty surfaces: Reduces adhesion by 90%, causing peeling in under 1 year.
- Skipping 24-48 hour dry time post-wash: Traps moisture, leading to blisters in 60% of jobs.
- Ignoring primer on bare wood: Allows tannin bleed, requiring full repaint within 2 years at $3,000+ cost.
- Using wrong PSI on pressure washer: Over 3000 PSI gouges siding ($500 repair); under 1500 PSI leaves residue.