10 Questions to Ask Before Signing a Crawl Space Encapsulation Contract (2026)

1. What thickness vapor barrier do you install, and what is the warranty?

Professional encapsulation uses 20-mil reinforced polyethylene vapor barrier (minimum) — this thickness resists tears during installation, foot traffic for future maintenance, and does not degrade from soil chemical contact. Budget contractors use 6-12 mil barriers that tear easily and require replacement within 5-10 years. Ask for the specific product name and manufacturer warranty. A 25-year barrier warranty signals professional-grade material.

2 minutes to ask

Pro tip: Ask to see a sample of the barrier material. 20-mil feels substantial and resists puncture from a pen push. 6-mil feels like heavy trash bag material. The difference is immediately obvious by touch.

2. How do you seal the barrier to walls, piers, and penetrations?

A vapor barrier laying on the ground does not constitute encapsulation. True encapsulation requires the barrier to be sealed to foundation walls (typically 6-12 inches up the wall, mechanically fastened and sealed with mastic or tape), wrapped around support piers, and sealed around all pipe, wire, and duct penetrations. Any gap or unsealed edge allows moisture to bypass the barrier. Ask specifically how each interface is handled.

5 minutes

Pro tip: Ask: 'If I inspect 6 months after installation, what would a gap or failure point look like?' A contractor confident in their sealing method will describe exactly what proper sealing looks like and invite inspection.

3. What dehumidifier do you install, and what capacity is it?

An encapsulated crawl space without a dehumidifier is a sealed box that cannot manage residual moisture or seasonal fluctuations. The dehumidifier must be commercial-grade (not a residential box store unit), sized for the crawl space volume, and equipped with a condensate pump and drainage line. Typical sizing is 70-90 pint/day capacity for 1,000-1,500 sqft crawl spaces. Ask the specific model, capacity, and whether it has a warranty independent of the encapsulation warranty.

5 minutes

Pro tip: Ask about the dehumidifier's power consumption and annual operating cost. Commercial crawl space units run $50-$150/year in electricity. If no one mentions this ongoing cost, they may be installing an undersized unit that runs constantly.

4. How do you handle existing standing water or bulk water entry?

If your crawl space has standing water, encapsulation alone does not solve the problem — it seals water inside. The contractor must first address the water source: exterior grading, gutter discharge, foundation wall cracks, or high water table. Solutions may include a sump pump (under the barrier), interior perimeter drainage, or exterior waterproofing. A contractor who proposes encapsulation over standing water without addressing the source is selling you an expensive failure.

5 minutes

Pro tip: Ask: 'What happens if water enters after encapsulation — where does it go?' The answer should involve a sump system or drainage path, not 'it won't happen.'

5. Will you close the foundation vents, and how?

Traditional crawl space vents (required by old building codes, now contradicted by current science in most climates) allow humid exterior air to enter and condense on cooler crawl space surfaces. Proper encapsulation closes these vents permanently — typically with rigid foam insulation sealed and covered with the barrier material. Ask whether vent closure is included and whether the contractor will handle any code compliance documentation needed for closing vents in your jurisdiction.

2 minutes to ask

Pro tip: Some jurisdictions still require open vents by code even though building science contradicts this. Ask whether the contractor handles the code variance or exception process, or whether that falls to you.

6. What insulation is included, and where is it placed?

Encapsulation often includes insulation — but the type and placement matter. Rigid foam on crawl space walls (R-10 to R-15) is the current best practice for conditioned crawl spaces. Some contractors instead insulate the floor joists above (fiberglass batts) and leave walls uninsulated — this is the old approach for vented crawl spaces and contradicts encapsulation principles. Wall insulation makes the crawl space part of the conditioned building envelope.

5 minutes

Pro tip: If the contractor proposes fiberglass batt insulation in the floor joists above an encapsulated space, they are mixing two incompatible approaches. Encapsulated spaces should have wall insulation, not floor insulation.

7. What is the total project warranty, and what does it actually cover?

Ask for the warranty document before signing. Key questions: Does it cover labor and materials, or just materials? Does it cover moisture-related damage (mold, wood rot) that occurs after installation? Is there a humidity performance guarantee (e.g., below 55% RH)? Who is responsible for dehumidifier failure — you or the contractor? A contractor confident in their system offers meaningful performance warranties, not just material defect coverage.

15 minutes to review warranty

Pro tip: Ask: 'If relative humidity exceeds 60% after installation, what do you do at no charge?' The answer reveals whether their warranty is performance-based or just covering material defects.

8. How do you handle pest and termite inspection access after encapsulation?

Annual termite inspections require visual access to foundation walls and wood framing. An encapsulation system that covers 100% of foundation walls can interfere with termite inspection requirements. Professional installers leave a 3-inch inspection gap at the top of foundation walls (barrier terminates below the sill plate) so inspectors can observe mud tubes. Ask how they maintain pest inspection access without compromising the moisture barrier.

2 minutes to ask

Pro tip: Ask your termite inspection company what access they need before the encapsulation is installed. Share those requirements with the encapsulation contractor so they design around inspection needs from the start.

9. What is the maintenance schedule, and is it included?

Encapsulated crawl spaces are not install-and-forget. They need annual inspection of barrier integrity, dehumidifier function, sump pump testing (if present), and drainage system verification. Some contractors include the first 1-2 years of maintenance visits in their contract. Others hand you a maintenance manual and leave. Understand what ongoing attention the system requires and whether you will do it yourself or pay for annual service visits ($100-$200/year).

5 minutes

Pro tip: Ask for a written maintenance checklist that you can follow yourself. Most maintenance is simple (check dehumidifier, test sump, visual barrier inspection) but needs to actually happen annually.

10. Can I see a completed project from 3+ years ago?

A newly installed encapsulation looks great. The real test is how it performs after 3-5 years of actual conditions — soil settling, seasonal moisture cycles, and dehumidifier wear. Ask to see (or receive photos/video of) a project completed at least 3 years ago. If the barrier is still sealed, the space is dry, and no mold has appeared, the contractor's method and materials are proven in real conditions, not just on installation day.

30 minutes

Pro tip: Ask the reference homeowner: 'Has the contractor returned for any warranty work?' If yes, what for? This reveals common failure points in that contractor's method and how responsive they are to post-installation issues.

Bonus Tip

Install a hygrometer with remote monitoring before getting quotes

Place a $25 wireless hygrometer in your crawl space for 30 days before calling contractors. Record humidity highs and lows across different weather conditions. This data helps you evaluate contractor proposals against actual conditions — and prevents a contractor from either understating or overstating your moisture problem to justify their preferred scope.

What to Avoid

  • Signing a contract that does not specify barrier thickness, dehumidifier model, and whether vent closure is included — vague scopes lead to disputes over what was promised.
  • Choosing encapsulation when the primary issue is bulk water entry that needs drainage solutions first — encapsulation manages moisture vapor, not liquid water flow.
  • Accepting a quote without drainage provisions if your crawl space has any history of standing water — the next heavy rain will fill your sealed space like a pool liner.
  • Installing encapsulation yourself with hardware store materials — improper sealing techniques create trapped moisture pockets that accelerate the problems encapsulation is meant to solve.