Every Week: Clean the Pool
Remove debris before it sinks, stains or feeds algae. Do these in order, since each step makes the next one easier.
-
Skim leaves and debris off the surface
Use a flat or bag net on a telescoping pole and work around the whole pool. Debris that stays on top is easy to remove; once it sinks it stains the floor and uses up chlorine as it breaks down.
-
Empty the skimmer and pump baskets
Turn the pump off before opening the pump lid, empty both baskets, check the lid o-ring and restart. Full baskets cut water flow, which weakens filtering and makes the pump work harder.
-
Brush the walls, steps and waterline
Brush toward the main drain, paying attention to corners, steps and behind ladders where water moves least. Use a nylon brush on vinyl and fiberglass and a stiffer brush on plaster. Brushing lifts the film that algae needs to take hold.
-
Vacuum the floor
Vacuum by hand or run the automatic cleaner, then empty its bag or canister. Do it after brushing so the loosened dirt has settled. Fine dust that returns through the jets means the filter needs attention.
-
Check the water level
The level should sit about halfway up the skimmer opening. Top up with a garden hose if it is low, since a pump that draws air can overheat. Losing more than about a quarter inch a day in mild weather is worth a leak check.
Every Week: Test and Balance the Water
Test after cleaning and before adding anything. Adjust one thing at a time with the pump running.
-
Test free chlorine and pH
Use test strips or a drop kit on a sample taken elbow-deep, away from the return jets. Typical targets are 1-3 ppm free chlorine and a pH of 7.2-7.6. In hot weather or heavy use, test two or three times a week.
-
Test total alkalinity and adjust it before pH
The typical target is 80-120 ppm. Alkalinity steadies the pH, so correct it first, then bring the pH into range with an increaser or reducer, dosing by the label for your pool volume.
-
Add sanitizer
Refill the chlorinator or floater with tablets, or add liquid chlorine in the evening so sunlight does not burn it off at once. For a salt pool, check the generator output setting instead. Never add chlorine through the skimmer unless the product label says to.
-
Shock when the water needs it
Shock after heavy use, a rainstorm, a strong chlorine smell or a combined chlorine reading above about 0.5 ppm. Many owners do it every one to two weeks in midsummer. Add it at dusk, run the pump overnight and wait until chlorine is back to 1-3 ppm before swimming.
Every Week: Check Circulation and Equipment
A two-minute look at the equipment pad catches most problems while they are still small repairs.
-
Read the filter pressure gauge
Note the pressure when the filter is clean and write it on the tank. When the gauge reads 8-10 psi above that number, backwash the sand or DE filter or rinse the cartridge. A reading well below normal points to a blockage ahead of the pump.
-
Confirm the pump run time
The pump should move all the water through the filter at least once a day, which is typically 8-12 hours for a single-speed pump in summer. Variable-speed pumps run longer at low speed for less power. Check that the timer has not drifted after a power cut.
-
Look and listen at the equipment pad
Look for drips at the pump seal, the filter band, the heater and the valves, and listen for grinding or a high whine. Air bubbles under the pump lid mean a suction leak or low water. A small leak fixed early is usually a minor repair of $100-$350 with parts.
-
Check the returns and the automatic cleaner
Aim the return jets slightly down and all in one direction so the water circles the pool. Make sure the cleaner covers the whole floor and its hose is not tangled.
Every Month: Deeper Checks
These tasks take about an hour and a half in total and keep the weekly routine working.
-
Run the full set of water tests
Once a month, test calcium hardness (typically 200-400 ppm), stabilizer or cyanuric acid (30-50 ppm for a chlorine pool) and, in a salt pool, the salt level against the range in the generator manual. Many pool stores test a water sample, or use a full drop kit.
-
Clean or backwash the filter
Backwash sand and DE filters until the sight glass runs clear, then add fresh DE if you have that type. Hose off cartridges from top to bottom between the pleats. Do it by the gauge, not the calendar, though once a month is typical in summer.
-
Inspect the salt cell, if you have one
Switch off the power, remove the cell and look for white scale on the plates. Rinse it with a hose and use a mild acid soak only as the manual describes, since over-cleaning shortens the life of the cell. Most cells need attention every two to three months.
-
Clean the tile line and check rails, ladders and safety gear
Wipe the waterline with a pool tile cleaner before the film hardens. Tighten ladder and rail bolts, check drain covers for cracks and confirm that gate latches and the safety hook or ring are in place.
-
Lubricate o-rings and check stored chemicals
Put a pool-grade silicone lubricant on the pump lid and filter o-rings so they seal and last. Keep chemicals dry, closed, apart from each other and out of direct sun, and replace old test strips or reagents.
Through the Season: Extra Tasks and When to Call a Pool Service
Weather, heavy use and equipment faults call for more than the weekly routine. Know which jobs to hand off.
-
Reset the pool after storms, parties and heat waves
Skim and empty baskets, test and shock, and run the pump for 24 hours. Heavy rain dilutes chemicals and washes in debris, and a full pool of swimmers uses chlorine quickly. Retest the next day before returning to the normal schedule.
-
Have the filter deep cleaned two to four times a year
A cartridge soak or a full DE grid teardown removes oils and scale that rinsing leaves behind. You can do it yourself with a filter cleaner, or a pool service typically charges $75-$150.
-
Act on the first sign of cloudy or green water
Test, brush, shock and clean the filter the same day. A light green pool caught in the first week is far cheaper to clear than a dark one: a professional cleanup runs $250-$400 for light green and $400-$700 for dark green.
-
Call a pool service for equipment faults
A pump that will not prime, a tripping breaker, a leaking filter tank, a heater that will not fire or a salt system showing a fault code are jobs for a technician. Service calls typically run $85-$150 per hour plus parts.
-
Decide whether to hire weekly service
Full weekly pool service typically costs $120-$250 per month with testing, basic chemicals, brushing, skimming and baskets. A chemical-only plan runs $70-$130 per month if you do the cleaning yourself. A one-time cleaning before a party or after a trip runs $150-$350.
Pro Tips
-
Keep a simple log
Write down the date, test readings, what you added and the filter pressure. A log shows trends, such as pH that climbs every week or pressure that rises faster than usual, long before the water looks wrong.
-
Pick one day and keep it
Chlorine and debris problems build quietly. A fixed weekly day, with a mid-week chlorine and pH test in the hottest months, prevents nearly all cloudy water.
-
Add chemicals in the evening
Sunlight breaks down unstabilized chlorine within hours. Dosing at dusk with the pump running gives it the whole night to work.
-
Brush even when the pool looks clean
Algae starts as a thin film you cannot see. Ten minutes of brushing a week is the cheapest algae prevention there is.
-
Ask what a service visit includes
If you hire weekly service, ask whether chemicals, filter cleaning and vacuuming are in the monthly price or billed separately, and how the technician reports each visit.
Common Mistakes to Avoid
-
Adjusting pH before alkalinity
When alkalinity is out of its 80-120 ppm range the pH will not hold. Correct alkalinity first, wait a few hours with the pump running, then adjust the pH.
-
Mixing or pre-mixing chemicals
Never combine pool products in a bucket or in the feeder, and never put different types of chlorine in the same container. Add each one to the pool separately, following its label.
-
Running the pump too little
Cutting the run time to save power leaves water unfiltered and chemicals unmixed. Dropping below one full turnover a day is a common cause of midsummer algae.
-
Cleaning the filter by the calendar only
A filter cleaned too rarely chokes the flow, while a sand filter backwashed too often wastes water and filters worse. Let the 8-10 psi rise on the gauge decide.
-
Skipping weeks while away
Two weeks without attention in hot weather is enough to turn a pool green. Arrange a neighbor to empty baskets and add chlorine, or book a one-time cleaning or temporary weekly service.